La Pavoni Europiccola - Boiler and body

It can happen that your old heating element for your La Pavoni Europiccola, La Pavoni Stradivari, La Pavoni Romantica or of your Gaggia 105-106 burns down or get’s a short in it. This specific model heating element gives 1000W at 240V made by the heating element manufacturer Backer. It is a full stainless steel element, so flange and the element. The...

The big spring shown on this page is a filterbasket spring. This filterbasket spring is used to keep the filterbasket in it’s place. This filter locking spring can be used on pre-millennium as well on Millennium La Pavoni portafilters. The La Pavoni part reference for this item is 311437 You can use this filter locking spring with single as well as with...

For the La Pavoni Europiccola, Professional and the Romantica there are 2 options to cover the plastic drain tray (371104). The stainless steel drain grid, or the plastic one.  On this page you will find the plastic version. This plastic grid has a horizontal grid pattern, instead of the metal one with a hole pattern. The plastic type of grid was...

On this page you will find the heating element gasket, which is an o ring, for the La Pavoni Europiccola, La Pavoni Professional, La Pavoni Stradivari, La Pavoni Romantica and the Gaggia 105-106. This specific gasket is only suitable in combination with the full stainless steel heating elements made by backer. They are not suitable for the earlier brass...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

For the La Pavoni Europiccola there haven been a variety of boiler fixing rings. It started in the 60ies with the steel boiler rings, from the 1980’s you will find the brass boiler rings. These have 3 m6 bolt holes for installing the heating element, there is also a attachment point for the ground wire. Around the turn of the century La Pavoni introduced...

The plastic base plate shown on this page is used with various domestic La Pavoni lever espresso machines. This base plate is a OEM/Original La Pavoni spare part. The La Pavoni part reference for this item is 371174. This plastic base plate is the later model. This base plate is installed from the bottom of espresso machine and held in place with a screw....

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from European walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...

The La Pavoni (and Gaggia) plastic drain tray (371104) is used on a variety of models like the La Pavoni Europiccola, La Pavoni Professional, La Pavoni Romantica and finally On the Gaggia 105(S371104). The plastic drain tray hasn’t been there from the beginning. The first la Pavoni’s had a flat surface where you needed to put your coffee cup. Later on,...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

Originally you would only find a boiler pressure manometer on the La Pavoni Professional espresso machines. This boiler pressure manometer is mounted on the top sight glass fitting. If you want to convert your La Pavoni Europiccola and fit it with a Pressure gauge, this is the kit you need The sight glass fittings used to have a internal diameter of...

This gasket is one of the few ones which does not need to seal off water. But is used as a gasket between 2 metal surfaces. This gasket can be used on various models of domestic La Pavoni lever espresso machines. The part reference for this item is 362019 This gasket has a outer diameter of 93mm a inner diameter of 80mm and a thickness of 2mm. You can use...

On this page you will find the heating element thermostat for the La Pavoni Europiccola, La Pavoni Stradivari and the La Pavoni Professional. This thermostat is also suitable for the Gaggia 105-106. The thermostat breaks the connection when the temperature becomes 127 degrees Celsius, this is a manual safety switch. The thermostat itself is suitable to...

La Pavoni brass heating element gasket made from AFM34

This item is a vacuum valve for various La Pavoni domestic lever espresso machines. This item is a OEM/Original La Pavoni spare part. The part reference for this item is 396754. This vacuum valve has been made from 2 brass components and a stainless-steel clip. The seal is made with the o ring around the shaft. You can use this vacuum valve on the La...

The big brother of the 1000W 120V is also available in 120V. The 1200W 120V heating element. This specific heating element is suitable for the La Pavoni Europiccola and the La Pavoni Mignon lever espresso machines. The La Pavoni product code is: 331337  As it’s smaller brother, this heating element is also completely made from stainless steel. The flange...

Every La Pavoni Europcciola, La Pavoni Stradivari and La Pavoni Professional is equipped with a boiler safety valve/pressure relief valve. This item can be used with the pre-millenium and the millennium models. With the earliest models when there is no pressure switch this is the main form of pressure relief of the boiler. The Boiler relief valve is...

The item on this product page is a OEM/Original La Pavoni spare part. This item is the rubber foot which goes underneath various La Pavoni and Gaggia domestic lever espresso machines. The part reference for this item is for Gaggia S371101 and for La Pavoni 371101. This rubber foot has a outer diameter of 30mm and can be installed in the base plates with...

Is the grid missing of your La Pavoni Europiccola(324021), Professional, Romantica or Gaggia G105(S324021). You can find the replacement grid on this page. To make your lever espresso machine complete again. This item is suitable for the Pre-millenium and millennium la Pavoni lever espresso machines. The grid has been made out of stainless steel and has...

The item on this product page is a steam valve knob for various La Pavoni lever espresso machines. This item is a OEM/Original La Pavoni spare part. The La Pavoni part reference for this item is 475010 This knob has a smooth brass insert. This knob is held in place with a spring pin. This steam valve knob has a silk printed symbol of steam printed on it...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from European walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...

The item on this product page is a OEM/Original La Pavoni spare part. This item is a boiler safety valve for various domestic lever espresso machines. The La Pavoni part reference for this item is 396751 This safety valve is only the body and not the internals of this valve.  This boiler valve has at the bottom a male M12 thread. You can use this on the...

It is always possible that your old heating element for your La Pavoni Europiccola, La Pavoni Romantica, La Pavoni Stradivari or your Gaggia 105 burns or gets a short. The other option is that you purchased a old model La Pavoni Europiccola and you want to convert your classic lever espresso machine to a proper 120V version. This model of heating element...

The double bipolar switch you see on this page can be used on the La Pavoni Europiccola domestic lever espresso machine. The La Pavoni part reference for this item is 435059. This switch can be used on Pre-millennium as well as millennium models. This double bipolar switch has been rated up to 16A at 250V. On the red switch is 0 an 1 been silk printed. On...

This specific type of switch is used for the La Pavoni Romantica, La Pavoni Europiccola for the configurations ERG, ELH, EL and EN. The part number for the La Pavoni is 435063.But this model of switch is also used on the Gaggia Factory 105 (S435063) This specific model red bipolar switch is a rocker switch with a pilot light. The mounting hole for this...

This is the bigger brother of the 1000W 230V heating element, it is the 1200W 230V heating element suitable for the earlier models of La Pavoni Europiccola and La Pavoni Mignon lever espresso machine. This heating element is also a complete stainless steel. The flange is made from a sheet of stainless steel, the outer diameter is 84mm. The coils are made...

This o ring is used on various domestic La Pavoni lever espresso machines. The La Pavoni part reference for this item is 465204. This o ring has been made from EPDM. The cord diameter is 3,53mm and the internal diameter is 28,17mm. This o ring has been made in Italy. You can use this on Millennium and Pre-Millennium La Pavoni models such as the La Pavoni...

If have a wreck of a la Pavoni Europiccola lever espresso machine or you want to give your La Pavoni Mignon a complete overhaul. This set would be ideal for you. This set made for la Pavoni espresso machines with a pre-millennium brewing group. This is a generic set, so it is possible that not all parts apply to your pre-millennium espresso machine....

The item on this page is a OEM/Original La Pavoni espresso machine part. This boiler knob can be used on various domestic lever espresso machines. This item has the La Pavoni part references 26872 and 47700308  This boiler knob screws in the top of the boiler. This boiler knob does not come with the sealing o ring. The knob has been made in the EU. You...

The item on this product page is a OEM/Original La Pavoni spare part. This item is a pressure switch manufactured by the Italian company Ma-ter. The La Pavoni part reference for this item is 451308. This pressure switch had been pre-set at 0,8 bar, but the pressure range goes from 0,5 up to 1,2 bar. The fitting used is a male ¼” BSP-G. The microswitch on...

The newer model of la Pavoni Europiccola and all the models of the Pavoni Professional use a modern pressure switch.  Currently those are the Ma-ter Echo pressure switches. Seen these can’t be installed directly into the heating element (the pressure switch would stick out the bottom off the base). For this problem they have found a solution. In the...

This tamper is made from from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...