Vibiemme Replica Pistone

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

This oddly looking screw is the left brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRPIS This screw can only be used on the left side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on the...

Fiorenzato group casting. this casting holds the lever assembly and the spring and piston assembly, offcourse only the casting. Return to the Fiorenzato lever parts overview

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

Ball valve 1/4M 1/4F

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

This oddly looking screw is the right brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRDPI  This screw can only be used on the right side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on...

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T  This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...

Faema E61 expansion valve gasket made out of nbr. This gasket makes sure that the expansion valve doesn't leak below the opening pressure of the valve. The gasket itself is seated in a valve guide which also has the function of spring guide for the expansion valve. Return to the Faema E61 valve parts overview

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

This flat PTFE gasket is used on various lever espresso machine brewing groups used on the brands Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200190  and the Vibiemme part reference number is GUARTEFANPIST. This flat gasket is made from PTFE. The outer diameter is 50mm, the inner diameter is 44mm and the thickness is 4mm. The gasket...

1/4" water charging valve autofill

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

Fiorenzato o ring 41,28x3,53mm o ring. This o ring seals the brewing group from the boiler.Return to the Fiorenzato Piazzo San Marco overview

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

O ring 14x2mm

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...

The portafilter gasket on this product can be used on various lever espresso machines. On brands such as Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200194  and the Vibiemme part reference number is GUARSOTPISTON. This portafilter gasket has a outer diameter of 65,5mm a inner diameter of 55,5mm and a thickness of 5,5mm. This gasket...

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...