Brasilia coffee machine parts
The item on this product page is a steam and water valve screw, used on various Brasilia espresso machines. The Brasilia part reference number for this item 00107.4.00.04 This articulating valve screw is used in combination with the spring washers and the conical PTFE gaskets to seal off the valve. This item has been made in Italy. You can use these...
€20.25
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Bezzera bottomless portafilter
Bezzera bottomless portafilterReturn to the portafilter overview
€60.39
Astoria front stop
On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...
€21.76
Beating rubber lever group
On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...
€11.74
Tap joint spring 12x15mm
The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...
€2.41
Brasilia upper level fitting
The water level fitting on this page can be used on various Brasilia espresso machine models. The Brasilia part reference number for this item are 00024.0.00.04 and 00024.0.00.04 This casted brass sight glass fitting has on the machine side a male 3/8” BSP-G thread, on water level side a female 3/8” BSP-G and on the bottom/top a female ¼” BSP-G thread....
€14.66
Fiorenzato o ring upper brewing group
A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...
€4.08
O ring 6.07x1.78mm Solenoid valve
This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.61
Fiorenzato o ring bottom
A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...
€3.44
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64
Male plug 1/4"
One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.
€2.72
Astoria lever fork pre 2001
Astoria lever group fork pre 2001 Return to the Astoria lever parts overview
€134.19
Rancilio flat copper gasket 24x20x1mm
The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...
€1.55
Faema E61 valve gasket 13x4x4mm
The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.74
Astoria group locking gasket 88x40x2mm
On this page you will find a group locking gasket. This group locking gasket is normally used with most Astoria espresso machine and some Wega machines, so not lever groups. But they are also suitable for the Astoria and Wega lever groups This gasket is made from a fibre material. The outer diameter is 88 mm, the inner diameter is 40mm and the thickness...
€6.97
Rancilio steam/water valve joint o ring 12,1x2,7mm
Rancilio steam/water valve joint o ring 12,1x2,7mm
€0.87
Sirai pressure switch single phase P203/T01 20A
The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
€90.16
Water level nut
This sight glass fitting is used on a variety of espresso machine brands such as Vibiemme, La Scala, Brasilia and Gaggia. The Brasilia part reference is 00089.0.10.04 , the Gaggia reference is LV0505 and the Vibiemme (VBM) part references are RACCP227 and RACCP427. This sight glass fitting has a male 3/8” BSP-G thread. The central hole is for the sight...
€6.42
Brasilia steam tap washer
The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03 These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...
€2.41
Brasilia heating element 1800W 220V
On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...
€95.36
Brasilia tab gasket conical
This Conical PTFE gasket can be used on a variety of Brasilia espresso machines. For this item there is a Brasilia part reference of 00810.0.00.02. This gasket has a conical shape. The outer diameter of this PTFE gasket is 14,5mm, the inner diameter is 10mm and the thickness is 5mm. This gasket can be used on the rubber as well as on the ceramic valves....
€1.99
Brasilia rubber valve stud
The valve axle on this page is suitable for a variety of Brasilia espresso machine models. This steam and water valve shaft has the Brasilia part reference of 12046.4.00.09 This steam and water valve shaft has a overall length of 100mm and comes with a sealing gasket already installed. You can use this valve not in combination with the ceramic valves....
€19.03
Astoria back stop
On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...
€9.59
PTFE gasket 18x13x2mm
The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...
€1.15
O ring FKM 10.78x2.62mm
On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....
€1.05
Faema o ring 7,2X1,9mm nbr
On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...
€0.56
Astoria lever pin
On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...
€20.16
Paper shim 66x58x0,8mm
On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...
€1.10
