Brasilia coffee machine parts
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€8.70
Bearing holder pin
On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...
€18.92
Beating rubber lever group
On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...
€10.21
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€94.94
PTFE gasket 18x13x2mm
The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...
€0.92
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€12.87
Brasilia steam tap screw
The item on this product page is a steam and water valve screw, used on various Brasilia espresso machines. The Brasilia part reference number for this item 00107.4.00.04 This articulating valve screw is used in combination with the spring washers and the conical PTFE gaskets to seal off the valve. This item has been made in Italy. You can use these...
€16.14
Lever group sleeve
On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...
€236.00
Tap joint spring guide
This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...
€0.96
Bezzera bottomless portafilter
Bezzera bottomless portafilterReturn to the portafilter overview
€48.15
Male plug 1/4"
One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.
€2.17
Brasilia heating element 1800W 220V
On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...
€67.63
Fiorenzato o ring bottom
A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...
€2.99
Rancilio flat copper gasket 24x20x1mm
The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...
€1.24
Brasilia tab gasket conical
This Conical PTFE gasket can be used on a variety of Brasilia espresso machines. For this item there is a Brasilia part reference of 00810.0.00.02. This gasket has a conical shape. The outer diameter of this PTFE gasket is 14,5mm, the inner diameter is 10mm and the thickness is 5mm. This gasket can be used on the rubber as well as on the ceramic valves....
€1.59
Brass nut M3
The nut on this page is a M3 nut made from brass. You will find this type of nut on variety of steam and water valves of Astoria and Wega espresso machines. The Astoria part reference for this item is 23050 and the Wega part reference is WY23050. This brass nut has a metric female thread of M3. The nut has made according to specifications of UNI 5587 and...
€0.68
Astoria group locking gasket 88x40x2mm
On this page you will find a group locking gasket. This group locking gasket is normally used with most Astoria espresso machine and some Wega machines, so not lever groups. But they are also suitable for the Astoria and Wega lever groups This gasket is made from a fibre material. The outer diameter is 88 mm, the inner diameter is 40mm and the thickness...
€5.55
Astoria back stop
On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...
€8.34
Faema E61 valve gasket 13x4x4mm
The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.59
Astoria front stop
On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...
€18.92