Brasilia Portofino leva

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...

The valve axle on this page is suitable for a variety of Brasilia espresso machine models. This steam and water valve shaft has the Brasilia part reference of 12046.4.00.09 This steam and water valve shaft has a overall length of 100mm and comes with a sealing gasket already installed. You can use this valve not in combination with the ceramic valves....

Seeger ring 9mm

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...

Astroia CMA style complete lever brewing group

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

Bezzera bottomless portafilterReturn to the portafilter overview

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

The item on this page is a steam and water valve washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item is 12153.0.00.03. This washer is made from machined brass. the outer diameter is 10,7mm, the inner diameter is 8,2mm and the thickness is 2mm. this washer is made in Italy. You can use this brass washer on...

Brasilia lower level fitting

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Brasilia portofino chromed steam pipe

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

This sight glass washer can be used on Gaggia and Brasilia water level assemblies.  This ring spreads the force equally over the sight glass gasket. The Brasilia part reference for this item is 00088.0.00.04 and the part reference for Gaggia is LV0506. This brass washer has a outer diameter of 15mm a inner diameter of 11,5mm and a thickness of 3mm. You...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

Brasilia portafilter single spout Return to the portafilter  overview

This sight glass fitting is used on a variety of espresso machine brands such as Vibiemme, La Scala, Brasilia and Gaggia. The Brasilia part reference is 00089.0.10.04 , the Gaggia reference is LV0505 and the Vibiemme (VBM) part references are RACCP227 and RACCP427. This sight glass fitting has a male 3/8” BSP-G thread. The central hole is for the sight...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

Safety valve 1/2"1,8 Certif CE PED IV

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

This Conical PTFE gasket can be used on a variety of Brasilia espresso machines. For this item there is a Brasilia part reference of 00810.0.00.02. This gasket has a conical shape. The outer diameter of this PTFE gasket is 14,5mm, the inner diameter is 10mm and the thickness is 5mm. This gasket can be used on the rubber as well as on the ceramic valves....

Brass lever valve with PTFE lining

On this page you will find a chrome plated lever group fork for various lever groups. This fork is responsible for transitioning the lever motion to a vertical motion. This chrome plated group fork can’t be used on the older AL lever groups as used by Astoria and Wega. That part is out of production. This specific item is OEM/Original item suitable for...

The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03  These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...

The o ring on this product page is used on various Brasilia steam and water valves on various models. The Brasilia part references for this item are 05825.0.00.02 and 0582500002. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 25,07mm. This o ring is made in Italy.  You can use this o ring on the Brasilia Century,...