La Pavoni Bar old

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...

La Pavoni o-ringReturn to the La Pavoni Bar lever group parts overview

La Pavoni Bar lever group shaftReturn to the La Pavoni Bar lever group parts overview

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

On this page you will find a group locking gasket. This group locking gasket is normally used with most Astoria espresso machine and some Wega machines, so not lever groups. But they are also suitable for the Astoria and Wega lever groups This gasket is made from a fibre material. The outer diameter is 88 mm, the inner diameter is 40mm and the thickness...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

La Pavoni copper gasketReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

La Pavoni inox ballReturn to the La Pavoni lever group parts overview

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

La Pavoni rubber ringReturn to the La Pavoni lever group parts overview

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...