Faema E61 spare parts
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.67
Bottom fitting for boiler pipe 1/2"M 1/2"M, hole 1/4"F
If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...
€18.82
Faema E61 expansion valve nipple
Faema E61 brass expansion valve nipple Return to the Faema E61 valve parts overview
€8.05
Faema front bakelite knob set
It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€40.37
Faema E61 steam valve pin
The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880 This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96
Faema E61 gasket PTFE 22x16x2mm
The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34
Fluidotech clamp ring pump 200L/H
On this page you will find a Fluid o Tech espresso machine pump. The model specification of this pump is Standard. This pump has a clamp ring connection, so a stainless steel clamp is used to connect it to the motor. This pump can pump 200 L/H and is equipped with a balanced bypass. The in and outlet of this pump have a 3/8” BSP-G thread. The pump has...
€132.57
Faema E61 glass plate srew set
Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91
Faema President and E61 2 group glass
It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€303.97
Compression spring 13x42mm
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...
€2.23
Faema E61 heating element 3 group 3700W 230V
The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...
€94.05
Faema E61 stickers
On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....
€11.07
Faema E61 non return valve body
Faema E61 brass non return valve body. The side flange is screwed into the main body.If you want to complete the assembly add the following parts to the part:Faema E61 Spring Non Return Valve; O Ring EPDM 8,9x1,9mm; Faema E61 Small Non Return ValveReturn to the Faema E61 valve parts overview
€33.38
Faema E61 cup warmer knob
Faema E61 plastic cup warmer knob. This knob is used on 2 locations on the Faema E61. The first location is on the regeneration valve. The second location is on the valve to controle the cup warmer ring. this ring is missing on most machines, but you can't miss the valve on a e61!
€4.78
Faema E61 complete steam valve
The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000 This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€77.47
Faema E61 water level spring
The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...
€3.82
Faema E61 microswitch lever control bracket
If you are restoring a Faema E61 or rebuilding a Faema E61 legend it is possible that you find a broken lever mechanism bracket. Now you can replace them. If you start the brewing process on your Faema E61 group, you raise your lever control arm. This pushes down the micro control lever. This control lever is attached to a metal rod. This metal rod is...
€6.24
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00
Faema E61 expansion valve guide
Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview
€5.11
Sirai pressure switch single phase P203/T01 20A
The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
€99.17
Faema E61 moustache set
On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71
Faema E61 filterholder gasket 8.5 mm
Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...
€3.38
Faema E61 brass camme lever rod
The item shown on this page is a cam shaft which is used on the Faema E61 and various other E61 style of brewing groups. Such as Bezzera and La Pavoni e61 style groups. The Faema part reference for this item 3161136650, the Bezzera part reference is 7479950 and for La Pavoni the reference is 314077. This brass cam shaft has a overall length of 82mm. The...
€20.10
E61 style lever brewing group
On this product page you will find a complete E61 style brewing group. There are a variety of E61 style brewing groups. Examples of this are the Solenoid valve groups, with the solenoid valve at the bottom, or on the sides. This E61 style brewing group can be used on Fiorenzato, Grimac and La Scala espresso machines. The Fiorenzato part reference fort his...
€402.24
Faema E61 steam tube
The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€34.99
Procon clamp ring pump 180 L/H
On this page you will find a espresso machine pump suitable for a variety of espresso machines. This pump has been made by the company Procon in Ireland. This model is a clamp ring pump, this pump is clamped with a stainless steel clamp to the espresso machine motor. The pump can pump 180 L/H and is fitted with a balanced bypass. To control the pump...
€174.64
Faema E61 Sticker 1 Group
Faema E61 sticker 1 group for the back glass plate of the machine. Return to the Faema E61 body parts overview
€19.22
Crushable copper washer 23x17x3mm
The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines. For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02 This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...
€1.72
Faema E61 water inlet valve guide
Faema E61 brass water inlet valve guide. You can use this valve guide for several faema models. But they are mostly used on the Faema E61. comes with the gasket Return to the Faema E61 water inlet overview
€35.73
Faema E61 steam/water group expanding spring
The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.48
Faema E61 PTFE gasket 26x21x2mm
This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52
Faema E61 plastic top 3 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 3 group are only the measurements of the width and length of the U shape.The length of this plexi is about 630mm and the width is 220mm. This cupwarmer...
€353.11
Faema E61 plastic top 2 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€325.64
Faema E61 valve gasket 13x4x4mm
The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81
Faema E61 brass washer
Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview
€0.38
