Vibiemme Replica manual

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

Vibiemme upper sleeve

When you have just used your steam wand to make a perfect latte. But you want to clean your steam wand, but you can’t because the metal is too hot. Don’t worry, we sell protective rubber sleeves which don’t pass on the heat so you won’t burn your hands. This specific model is suitable for a steam pipe which has a diameter of 10mm and has a length of 50mm....

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

The spring on this product page is used for various applications with various brands. This spring is used in water inlet systems, steam and water valves and non return valves. You will find this model of compression spring with brands such as Brasilia, La Spaziale, Faema, Grimac, Vibiemme and La Scala. This stainless steel compression spring has a outer...

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...

EPDM OR 4,47x1,78

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...

On this product page you will find a heating element suitable for various VBM heating elements. This heating element is suitable for 2 group Vibiemme boilers. The Vibiemme part reference is ELETRES2G4023. This heating element produces 4000W at 230V and has 4 connecting poles. The immersed length of the heating element is 330mm. the heating element has a...

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...

The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...

Complete valve spout 54,6mm

The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

Faema E61 brass upper round rod 40x4mm. screws in the valve gasket holder Return to the Faema E61 group parts overview

Locking group gasket

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...

Faema E61 spout breaker Return to the Faema E61 group parts overview

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

On this page you will find a brass steam pipe bushing. But what is a pipe bushing. A pipe bushing makes it possible to move the steam and water wand freely without leaking. So how does it work? Well the pipe bushing has on the valve side 2 o rings, these seal against the side of the inside of the valve. But on the top ring of the pipe bushing there is...