Faema Urania

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

Faema lever group cap Return to the Faema Zodiac lever parts overview

Faema ring  Return to the Faema Zodiac lever parts overview

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....

On this page you will find the Faema lever back bumper. This rubber piece dampens the return of the lever into it’s resting position. Over time this rubber get’s damages or perishes. You can use this bumper on all Faema lever brewing groups like the ones on the Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania and the Faema Lambro.

The valve spring on this page is used in the Faema Zodiac group type, not all brewing groups use this model. This spring is there to keep pressure on the stainless steel ball bearing of 8mm. This valve spring is made from stainless steel and has a outer diameter of 8mm and a overall length of 20mm.

On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...

Faema top valve cap

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

Faema retention valve body Return to the Faema Zodiac lever parts overview

Is the lever fork on your Faema Lever group worm out, this is the solution for it. When you have a aluminium lever fork or brass one where there is slack on the lever pint, it is time to replace it. The item on this page is a brass casted and chrome plated lever fork for the Faema lever brewing groups, of course not for all models. You can use this model...

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

All the Faema Lever brewing groups use ball bearings to function properly, they are not all the same btw. The ball bearing set on this page is suitable for the Faema President, Faema Urania, Faema Lambro, Faema Mercurio (with the zodiac type group) and the Faema Zodiac group type. The Faema Marte and first series of the Faema Mercurio use a different...

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...

On this product page you will find a boiler gasket suitable for various Faema Urania boilers. This item is suitable for the first series of Faema Urania espresso machines. Not for the later ones which have similar boiler styles as the E61 and president. This PTFE boiler gasket has a outer diameter of 195mm a inner diameter of 155mm. The gasket has 9 holes.

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio and Faema Lever brewing groups. The outer diameter of this piston gasket is 50mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio Z9,...