Faema Urania

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

Have you ever wanted to convert your single group Faema lever espresso machine from a 220-230V version to a 110V version, now you can. The heating element on this product page is suitable for installation on various antique Faema Lever groups and regular Faema E61 groups. This heating element has the typical Faema type of brass flange. The element is...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

Faema top valve cap

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

Faema Mercurio/marte group gasket made from FDA graded fiber material

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

Faema guide ring Return to the Faema Zodiac lever parts overview

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...

Faema Urania 9 hole aluminium boiler flange ring. This flange ring is not suited for the E61 style boiler flange ring.Return to the Urania boiler parts overview

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...