Faema President

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

We where unable to trace down original or reproduction lever handles for the Faema E61 boiler filling valve. So we decided to have them casted ourselves. Seen the alternative would be a plastic handle which didn’t look like at all. We had made a casting mould and have a limited amount made of this Faema E61 aluminium filling handles. You will find this...

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

Faema retention valve body Return to the Faema Zodiac lever parts overview

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview

Faema top valve cap

Faema E61 brass water inlet valve guide. You can use this valve guide for several faema models. But they are mostly used on the Faema E61. comes with the gasket Return to the Faema E61 water inlet overview

On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

Faema aluminium drain tray. Return to the Faema E61 valve parts overview

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...

Faema ring  Return to the Faema Zodiac lever parts overview

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

On this page you will find the Faema lever back bumper. This rubber piece dampens the return of the lever into it’s resting position. Over time this rubber get’s damages or perishes. You can use this bumper on all Faema lever brewing groups like the ones on the Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania and the Faema Lambro.