Faema President

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...

Faema aluminium drain tray. Return to the Faema E61 valve parts overview

Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

The valve spring on this page is used in the Faema Zodiac group type, not all brewing groups use this model. This spring is there to keep pressure on the stainless steel ball bearing of 8mm. This valve spring is made from stainless steel and has a outer diameter of 8mm and a overall length of 20mm.

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...

Faema top valve cap

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio and Faema Lever brewing groups. The outer diameter of this piston gasket is 50mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio Z9,...

Faema ring  Return to the Faema Zodiac lever parts overview

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview

Faema guide ring Return to the Faema Zodiac lever parts overview

On this page you will find the Faema lever back bumper. This rubber piece dampens the return of the lever into it’s resting position. Over time this rubber get’s damages or perishes. You can use this bumper on all Faema lever brewing groups like the ones on the Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania and the Faema Lambro.

On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...

We where unable to trace down original or reproduction lever handles for the Faema E61 boiler filling valve. So we decided to have them casted ourselves. Seen the alternative would be a plastic handle which didn’t look like at all. We had made a casting mould and have a limited amount made of this Faema E61 aluminium filling handles. You will find this...

On the back of the Faema Zodiac brewing group is a top nut and a bottom nut. The top nut needs to be sealed off. Otherwise the water will leak out of it. You would have the choice of a fibre gasket but also a PTFE gasket. On this page you will find the PTFE gasket. The dimensions of this PTFE gasket measure a outer dimension of 15mm a inner dimension of...