Faema President

Faema guide ring Return to the Faema Zodiac lever parts overview

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

Have you ever wanted to convert your single group Faema lever espresso machine from a 220-230V version to a 110V version, now you can. The heating element on this product page is suitable for installation on various antique Faema Lever groups and regular Faema E61 groups. This heating element has the typical Faema type of brass flange. The element is...

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...

Faema aluminium drain tray. Return to the Faema E61 valve parts overview

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

We where unable to trace down original or reproduction lever handles for the Faema E61 boiler filling valve. So we decided to have them casted ourselves. Seen the alternative would be a plastic handle which didn’t look like at all. We had made a casting mould and have a limited amount made of this Faema E61 aluminium filling handles. You will find this...

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...

Faema lever group cap Return to the Faema Zodiac lever parts overview

On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...