Faema Urania

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

Faema Urania 9 hole aluminium boiler flange ring. This flange ring is not suited for the E61 style boiler flange ring.Return to the Urania boiler parts overview

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

Faema guide ring Return to the Faema Zodiac lever parts overview

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...

On this page you will find the Faema lever back bumper. This rubber piece dampens the return of the lever into it’s resting position. Over time this rubber get’s damages or perishes. You can use this bumper on all Faema lever brewing groups like the ones on the Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania and the Faema Lambro.

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...

On this product page you will find a boiler gasket suitable for various Faema Urania boilers. This item is suitable for the first series of Faema Urania espresso machines. Not for the later ones which have similar boiler styles as the E61 and president. This PTFE boiler gasket has a outer diameter of 195mm a inner diameter of 155mm. The gasket has 9 holes.

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...

The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...

Faema retention valve body Return to the Faema Zodiac lever parts overview

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio and Faema Lever brewing groups. The outer diameter of this piston gasket is 50mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio Z9,...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

Faema top valve cap

On this product page you will find a set of brass nuts and bolts used for the Faema Urania first series and Faema Urania second series. It does happen that these screws and bolts are missing, or just broken off during disassembly This kit contains in total 6 pieces, so 2 for the bottom, 2 for the top and 1 for the side. This item has been made in the EU.

Faema ring  Return to the Faema Zodiac lever parts overview

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...