Faema Urania varaosat

Faema Urania - varaosien valikoima

Faema Spare Parts - Urania

Tuotteita yhteensä 59 kpl.

Näytetään 1-36 yht. 59 tuotteesta

Faema E61 -näkölasi 12x175m m

Tällä sivulla olevaa nähtävyyslasia käytetään useissa Leverin espressokoneissa Faeman brändin toimesta. Näkölaseja voidaan käyttää esimerkiksi Faema E61:n, Faeman presidentin ja Faema Lambron espressokoneen mallissa.Näkölasin halkaisija on 12 mm ja kokonaispituus 175 mm. Lasi on valmistettu Italiassa.Tämän näkölasin tiivisteessä on ulompi halkaisijaltaan...
5,22 €

Vipuryhmän kuitutiiviste 22x17x2mm

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...
2,54 €

Faema E61 lämmityselementti 1 ryhmä 1500W 110V

Oletko koskaan halunnut muuttaa ryhmääsi? Faema vipu espressokone 220-230V versio 110V versio, nyt voit. Tämän tuotesivun lämmityselementti soveltuu erilaisiin Faema Lever -ryhmiin ja säännöllisiin Faema E61 -ryhmiin.Tällä lämmityselementillä on tyypillinen Faema-tyyppinen pronssi. Elementti on 110V ja toimittaa 1500W. Elementin pituus on vain 150...
97,78 €

Sirai painekytkin yksivaiheinen P203/T01 20A

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
90,16 €

Faema lever joint guide right

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...
6,97 €

Faema E61 FDA-kuitukattila 12 reikää 245x205x2mm

Tällä tuotesivulla löydät kattilakaappauksen joillekin Faema E61:lle, Faeman presidentille ja Faema Lambron espressokoneille. Tämä tiiviste toimii yhdessä kattiloiden kanssa, joilla on erillinen lämmityselementin lippu ja vesitason lippu tai yksi kattila, jossa on lämmityselementin lippu. AFM34:stä valmistettu polttoaine on Saksassa. Tämä tiiviste on...
30,34 €

Faema venttiilin jousi 8x20mm

The valve spring on this page is used in the Faema Zodiac group type, not all brewing groups use this model. This spring is there to keep pressure on the stainless steel ball bearing of 8mm. This valve spring is made from stainless steel and has a outer diameter of 8mm and a overall length of 20mm.
5,76 €

Faema lever joint guide left

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...
9,60 €

Faema lasitukisarja

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
45,30 €

Faema E61 lämmityselementti 1 ryhmä 1500W 230V

Tämän tuotesivun elementti on ihanteellinen antiikkivipun espressokoneelle tai Faema E61 -espressokoneelle.Tällä lämmityselementillä on tyypillinen Faema-tyyppinen pronssi. Elementti on 230V ja toimittaa 1500W. Elementin pituus on vain 145 mm.Tähän elementtiin käytettävän lämmityselementin halkaisija on 57 mm sisäinen halkaisija 43 mm ja paksuus 3 mm.Voit...
93,16 €

Fae E61 -vesilähde

Tämän sivun kevät on vesitason kevät ja sitä käytetään useissa vanhemmissa Faema-espressokoneissa. Sitä voidaan käyttää espressokonemalleissa Faema E61:nä, Faema-presidenttinä ja Faema Lambrona.Tämän ruostumattoman teräksen kevään halkaisija on 22 mm ja korkeus 20 mm.Huomautus: Tämä tuote ei sovellu Faema E61 -legendalle ja Faema E61 -juhlille.
3,47 €

Suihku 57 mm

Vipun panimoryhmä käyttää hieman eri osia, sitten normaali pumpun ajama espressokone. Tämä on sama juttu käytettyjen suihkujen kohdalla. Tämä italialaisen IMS Filtri -yhtiön tekemä suihkuruutu on tästä esimerkki. Tämä suihkunäytös kietoutuu panimoryhmän hihnan ympäri pitääkseen sen paikoillaan. Tämän suihkunäytön ulompi halkaisija on 57 mm Tämä suihku on...
12,79 €

Suodattimet 72,5x57x8 mm

Tällä tuotesivulla löydät portafilter-kaasun, joka sopii erilaisiin antiikkisiin Faema-espressokoneisiin. Faema Marte, Faema Mercurio, Faema E61 Tämä portafilter-kaasun halkaisija on 72,5 mm sisäinen halkaisijaltaan 57 mm ja paksuus 8 mm. Tuote on valmistettu NBR:stä. Kuten aiemmin mainittiin, voit käyttää tätä erilaisissa Faema-malleissa, kuten...
3,67 €

Faema E61 -lämpöelementti 2440/2900W 220/240V

Tällä tuotesivulla löydät lämmityselementin, joka sopii hyvin asennettavaksi Faema E61 2 -ryhmäkattilaan. Se toimii yhtenä vaiheena ja antaa vielä tarpeeksi valtaa 2-ryhmälle E61.Lämmityselementti tuottaa 2440/2900W klo 220/240V, elementissä on 4 johdotusta navat. Lämmityselementin keskellä on myös tilaa lämmityselementin termostaatille...
85,61 €

Asco/Sirai painekytkin P303/T01 3-vaiheinen 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
88,64 €

Faema Urania 9-reikäinen kattila

Tällä tuotesivulla löydät kattilan, joka sopii erilaisiin Faema Uranian kattiloihin. Tämä tuote sopii ensimmäiseen Faema Uranian espressokoneiden sarjaan. Eivätkä ne, joilla on samankaltaisia kattiloita kuin E61 ja presidentti. PTFE-kattilakaasun halkaisija on 195 mm sisäinen halkaisijaltaan 155 mm. Ruokalissa on 9 reikää.
39,46 €

Faema Bakelite Knob (käytetty)

On melko yleistä, että vanhassa Faema E61:ssä tai Faeman presidentissä Bakelite-ruumiitit puuttuvat tai ovat rikki. Mitä nämä paneelit tekevät? Koneen takaosa on koneen edessä. Faema E61:n ja Faeman presidentin etulevyssä on neljä lankaa. Näillä neljällä langalla voit ruuvata nämä Bakelite-ruuvit pitääksesi selkäsi paikoillaan.Faema E61:ssä Vastaavia...
36,70 €

Lever group spring 168x46mm stainless steel

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...
35,83 €

Faema säätimen sauva

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...
21,76 €

Faema viver -ryhmä takaisin kumipuskuriin

Tältä sivulta löydät Faema-vipua takaisin. Tämä kuminauha vaimentaa vivun palautumista lepoasentoon. Ajan mittaan tämä kumi saa vahingot tai katoaa.Voit käyttää tätä puskuria kaikissa Faema-vivun panimoryhmissä, kuten Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania ja Faema Lambro.
4,14 €

Ruostumaton teräspaine vaihdetaan

Painekytkin on valmistettu ruostumattomasta teräksestä 304. Rannekkeen pituus on 90 mm ja leveys 18 mm. Tämän rannekkeen tarkoituksena on korjata yksi puoli kattilokeroon tai kattilan väliin (enintään M10).Toinen puoli sopii painekytkentään 1/4" BSP-G-liittimellä.
10,48 €

V-tasoinen männin tiivistys 51x38x7.5mm

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...
3,60 €

Faema jousi 14x23mm

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.
4,97 €

Faema-vipuryhmän etupysäytys

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...
4,93 €

Faema E61 lämmityselementti 3 3700W 230V

Tällä sivulla näkyvä lämmityselementti sopii erilaisiin kolmeen ryhmään Faema espressokonemalleja, kuten Faema E61, Faema President ja Faema Urania.Tuote on 220V 3700W. On neljä napaa. Elementin pituus on 455 mm. Lippu on tyypillinen Faema-tyylinen lippu 95x57mm. Lipun keskellä on myös varaputki lämmityselementin termostaatille.Tämän elementin vastaavan...
85,50 €

Faema-vipuryhmän jousi 46mmx169mm

The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...
17,21 €

Faema Aluminium ryhmäpää

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...
322,51 €

Asco (Sirai) painekytkin P302/6

Asco P302/6 a 3 -vaiheen painekytkin on todennäköisesti kaikkein käytetyin. Tätä painekytkintä on käytetty espressokoneissa, kuten: La Marzocco, Faema, Cimbali, AstoriaWega, Nuova Simonelli, La Spaziale San Remo ja niin edelleen. Asco on ollut Sirai-yhtiö, koska nimi on muuttunut, mutta tuote pysyy ennallaan.Painekytkin on 3 napaa 30A painekytkin....
74,07 €

IMS E61 -tyylinen suihkuseinä

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
22,75 €

Portafilter tiiviste 73x57x9mm punainen silikoni

Tässä tuotteen sivulla löydät kannettavan suodattimen tiivistelmän, joka ei kuitenkaan ole tavallinen. Tämä kannettava suodattimen tiiviste on valmistettu ruokakasvaisesta silikonista punaisessa värissä.  Tämä tuote on valmistettu Italiassa. Pakkauksen ulkopinnalla on halkaisija 73 mm, sisäpuolella 57 mm ja paksuus 9 mm. Voit käyttää tätä monenlaisissa...
4,14 €

Faema E61 höyrypussi

Tätä vaskipesua käytetään useissa vanhemmissa Faema vipu espressokoneissa. Faema-osan viittaus tähän kohtaan on 41535931.Tätä pesua käytetään yhdessä puristuskevään kanssa pitääkseen yhtä painetta eri akselivetyille. Löydät tämän kohteen eri sovelluksissa, höyryventtiilit, vesiventtiilit ja veden sisääntuloventtiilit.Ulkoiset halkaisijat ovat 15 ja 9mm....
2,32 €