The item on this page is a OEM/Original La Pavoni espresso machine part. This boiler knob can be used on various domestic lever espresso machines. This item has the La Pavoni part references 26872 and 47700308 This boiler knob screws in the top of the boiler. This boiler knob does not come with the sealing o ring. The knob has been made in the EU. You...
Tällä sivulla löydät tarroja, jotka kulkevat vintage Faema E61:n ja Faeman presidentin viver-ryhmän etupaneelissa. Ne voivat vahingoittua tai olla olematta läsnä. Tämä sarja sisältää Faema-veden tarra kuvaukset, Massimo ja Minimo. höyryventtiili Vapore, vesiventtiili Scarico tuttu. Kuppi lämpimämpi venttiili Scaldatazze. Uudelleensyntymiseen Rigenerazione.
This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from European walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...
On this page you will find a silicone sight glass gasket, with this seal there is a water tight seal between the glass and the body. This gasket can be used on the Elektra Microcasa lever espresso machine. This item has the Elektra part reference of 00119035 This silicone gasket has a outer diameter of 15mm a inner diameter of 9mm and a thickness of 8mm.
Tällä sivulla löydät kamppailumme VAM Caravelin ja Arrarex Caravelin espressokoneille. Kahvitallilla on halkaisijaltaan 43 mm. Tamper-pohja on valmistettu ruostumattomasta teräksestä, kahva on valmistettu puusta. Se on italialainen walnut. Varmista, ettet kahvaa vedessä. Tärkeintä on, minkä mallin VAM ja Arrarex Caravel ovat? Tätä tamperia voidaan käyttää...
The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
The o ring on this product page is used on various Brasilia steam and water valves on various models. The Brasilia part references for this item are 05825.0.00.02 and 0582500002. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 25,07mm. This o ring is made in Italy. You can use this o ring on the Brasilia Century,...
Tältä tuotesivulta löydät tiivistelmän, joka soveltuu VAM Caravel- ja Arrarex Caravel -vipukoneisiin. Tämä malli ei sovellu Arrarex Caravelin muihin malleihin, ja se on 1,0-1,3 mallia. Tässä tiivistelmässä on seuraavat asiat niissä.1x Sillicone Portafilter Gaket 1x Sillicone o-rengas; 2x hpu mäntylevytSilikoni sormus ei ole välttämätön VAM 1.0...
It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
Tämän sivun kevättä käytetään Faema E61:ssä ja muissa E61-tyyleissä. Tätä kevättä käytetään kammiossa. Tämä kevät on pakattu kameran akselikokoonpanoon. Tämän puristuksen ansiosta kameran akselit tiivistävät aina akselia. Tällä ruostumattomasta teräksestä koostuvalla keväällä on ulompi halkaisijaltaan 15mm. Tämän kevään pituus on 25mm. Kevät on tehty...
On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...
This contact thermostat has a shut off temperature at 165 °celcius. In this case it is a manual espresso machine thermostat. That means that it needs to be pushed manually to reset. With a automatic one it will reset itself. On the bottom of this thermostat is a M4 male screw thread. You can screw the thermostat into a boiler for instance. For a brewing...
Tällä sivulla löydät pienennyksen. Tämä vähennys on toisella puolella naisen lanka ja toisella puolella mies lanka.Mieslanka on 3/8" BSP-G-lanka ja naislanka on 1⁄2"BSP-G-lanka.Tämä tuote on valmistettu Italian varastosta. On mahdollista, että saat tuotteen nikkelipinnoitteella.
This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
La Cimbali piston o ring 34,29X5,33mm. This thick o ring goes on the piston of a La Cimbali M20 lever brewing groupReturn to the La Cimbali M20 lever group overview
This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The lever cams do slide over this shaft. This item is not in production anymore.