Gaggia Italia Group - varaosat

The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.

This compression spring is vital in the lever mechanism used on the old Gaggia lever brewing groups. This spring is installed inside the side of the brewing group, with a small ball bearing on top of it. If this item is missing in your brewing group your brewing group mechanism won’t function properly. This compression spring is unfortunately out of...

Safety valve 1/2"1,8 Certif CE PED IV

This flat rubber gasket is used on a variety on Gaggia lever brewing groups. This flat gasket is used to seal of the regulator rod on the back of the brewing group. This gasket itself is made from NBR and is made in the Czech Republic.

Gaggia steel ballReturn to the Gaggia Italia group overview

Gaggia group locking gasket FDA gradedReturn to the Gaggia Italia group overview

Gaggia piston gasket

The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...

Tällä tuotesivulla löydät portafilter-kaasun, joka sopii erilaisiin antiikkisiin Faema-espressokoneisiin. Faema Marte, Faema Mercurio, Faema E61 Tämä portafilter-kaasun halkaisija on 72,5 mm sisäinen halkaisijaltaan 57 mm ja paksuus 8 mm. Tuote on valmistettu NBR:stä.Kuten aiemmin mainittiin, voit käyttää tätä erilaisissa Faema-malleissa, kuten...

The bearing is essential on a lever espresso machine brewing group. Otherwise it is not possible to transfer the lever movement in a vertical movement. In the brewing group of the Gaggia lever groups the bearings are embedded inside the group. On each side you will find one bearing where the pinion gear can ride on.

Gaggia piston boltReturn to the Gaggia Italia group overview

Gaggia portafilter supplement

The single filterbasket on this page can be used on a variety of Gaggia espresso machines. This filter basket is manufactured by the Italian company IMS filtri with the reference of GA1T182. This 1 coffee filterbasket can hold about 7 grams of ground coffee. The outer diameter of this filter basket is 68mm and the height is 24,5mm. The hole pattern is in...

The product on this page is a stainless steel piston for the Gaggia America and Gaggia Italia lever brewing groups. This piston has been made from 1 piece of stainless steel. The outer diameter of the piston is 50mm and the length is 82mm. The piston has the one way valve already installed. The piston also comes with a stainless steel shower screen with a...

Gaggia filterholder gasket 73,5x57,5x8,5mmReturn to the Gaggia Italia lever group parts overview

Gaggia short cammeReturn to the Gaggia Italia lever group parts overview

Gaggia filterholder springReturn to the Gaggia Italia lever group parts overview

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

Gaggia ryhmäsuihku dia 49mm

This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The  lever cams do slide over this shaft. This item is not in production anymore.

The filterbasket shown on this product page is a 2 coffee filterbasket suitable solely for a variety of Gaggia espresso machines. Domestic and commercial espresso models. This filter basket has been made by the Italian company IMS Filtri. The part reference for this basket from IMS is GA2T183. Note: this is not a competition basket. This stainless-steel...

Gaggia italia gasket and shim set. This set contains 4 inox shims and 4 v piston seals

This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.

Gaggia big cammeReturn to the Gaggia Italia lever group parts overview