La Cimbali piston o ring 34,29X5,33mm
La Cimbali piston o ring 34,29X5,33mm. This thick o ring goes on the piston of a La Cimbali M20 lever brewing groupReturn to the La Cimbali M20 lever group overview
€4.18
0
My cart
espresso machine brands
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Lever piston gasket 52x40x7mm
On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...
€5.20
Faema E61 steam/water valve gasket holder
On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€6.84
Lever group sleeve
On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...
€254.88
Faema E61 valve rod spring
This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.13
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€10.91
La San Marco lever group lip seal
La San Marco lever group lip sealReturn to the La San Marco spare parts overview
€5.90
Faema E61 expansion valve guide
Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview
€4.64
Victoria Arduino Supervat front lever stop
Victoria Arduino Supervat front lever stop. This stainless steel stop is a replacement for the original stop. This stop opens the brewing group valve.Back to the Victoria Arduino Supervat parts overview
€22.41
Gaggia XD heating element 2 gr 4000/4760W 230V
Gaggia XD heating element 2 gr 4000/4760W 230VType flangedwatt 4000/4760volt 220/240length (mm) 310
€118.75
Silicone gasket 12.3x5.6mm
Silicone gasket 12.3x5.6mm. Suitable for:CodeProducer95.05031 Carimali30370060 Expobar11181302 Futurmat-ArieteL165/5 Marzocco362074 Pavoni9007703 Reneka10505558 SanremoGUARSILRUBEVO VibiemmeGUARTECIECARK Vibiemme
€1.08
Bezzera valve gasket EPDM 14x4x4mm
The item on this product page is a flat EPDM gasket. This gasket is used on various Bezzera espresso machines as a water inlet valve gasket. This gasket has the Bezzera part reference numbers 5302502, 5493013 and 5493041. This flat gasket is made from EPDM. The outer diameter is 14mm, the inner diameter is 4mm and the thickness is 4mm.
€3.47
La Pavoni Europiccola single filterbasket pre-millenium
On this product page you can find the pre-millennium single filterbasket for the La Pavoni lever brewing group, this is only for the domestic lever espresso machines. This filterbasket is manufactured by the Italian company IMS filtri. This filterbasket has a outer diameter of 58mm and a height of 22mm. This filterbasket can hold around 6 grams of ground...
€7.19
Bezzera nipple
The item on this product page is a OEM/Original Bezzera nipple/shaft holder. This unit is used in various espresso machine models of Bezzera. The Bezzera part reference number is 5223402. This steam and water valve nipple/shaft holder is made from machined brass. The item is made in Italy. You can use this brass fitting on the Bezzera B2000, Bezzera...
€32.47
La Pavoni copper gasket
La Pavoni copper gasketReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview
€3.31
Elektra microcasa thermal insulator 107mm
On this page you will find a OEM/Original insulator used on the Elektra Microcasa lever espresso machine. This insulator is located between the base and the boiler.The part has a diameter of 107mm
€45.82
La Cimbali HX 150mm
La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...
€32.78
Astoria heating element 2 group 3700W 220V
The heating element on this page is quite a big model, which goes over 500mm. This specific heating element is made for Astoria and Wega espresso machine models with 3 brewing groups. This heating element is listed with Astoria under 17101 and with Wega the part number is WY17101 This heating element produces 3700W at 230/240V. The heating element has 4...
€105.17
Stainless steel filter 8.6x22.5mm
The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...
€3.47
Crushable copper gasket 18.7x13x2.5mm
On this product page you will find a round copper gasket, this copper gasket is of the kind which compresses when you tighten the nut above it. You will see this type of compressible copper gasket in combination on anti vacuum valves. The copper gasket on this page has a outer diameter of 18,7mm a inner diameter of 13mm and a thickness of 2,5mm. The...
€1.34
La San Marco balancer pin
La San Marco balancer pinReturn to the La San Marco brewing group parts overview
€10.72
- Out-of-Stock
Faema Mercurio third series pleixglass third series
Faema Mercurio third series pleixglass third series
€130.00
Faema E61 aluminium filling lever
We where unable to trace down original or reproduction lever handles for the Faema E61 boiler filling valve. So we decided to have them casted ourselves. Seen the alternative would be a plastic handle which didn’t look like at all. We had made a casting mould and have a limited amount made of this Faema E61 aluminium filling handles. You will find this...
€58.47
Inox ball return spring
The spring on this product page is used for various applications with various brands. This spring is used in water inlet systems, steam and water valves and non return valves. You will find this model of compression spring with brands such as Brasilia, La Spaziale, Faema, Grimac, Vibiemme and La Scala. This stainless steel compression spring has a outer...
€2.01
Faema Marte and Mercurio lever bearing
Lever ball bearing set for Faema Marte and Mercurio lever groups, only the early curved ones. For the later models Faema Mercurio you need to have a bigger bearing. click there.
€21.31
La Carimali piston spring
La Carimali piston spring Return to the Carimali lever parts overview
€35.67
La San Marco lever group plate
La San Marco lever group plate. To this plate the brewing group is fixed to.Return to the San Marco group parts overview
€93.77
PTFE gasket 35x30x2mm
The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...
€1.47
Elektra Microcasa bakelite portafilter handle M10
On this product page you will find the Bakelite handle used on various locations on the Elektra Microcasa a Leva. This lever handle can be used on the lever handle and as the portafilter handle. The part reference number of this part is 00469035 This Bakelite handle needs to be screwed into a metal stud which has a M10 thread (00186035)
€14.98
Arrarex Caravel: A Beacon of Innovation
Founded in the 1950s, Arrarex Caravel quickly rose to prominence with its groundbreaking lever operated espresso machines. The Caravel, the company's flagship model, combined compact design with innovative lever mechanisms, revolutionizing home espresso brewing. Loved for its simplicity and exceptional performance, the Caravel remains a beloved classic among coffee connoisseurs and collectors alike.
La Cimbali: Precision Engineering at Its Finest
La Cimbali, a stalwart in the coffee industry since 1912, is renowned for its commitment to precision engineering and superior quality. While best known for its commercial equipment, La Cimbali also produced exceptional lever operated machines. Models like the M1 showcased the brand's dedication to blending traditional lever brewing with modern technology, setting new standards for excellence in espresso craftsmanship.
Faema: Elevating Espresso to Art
Since its inception in 1945, Faema has been synonymous with innovation and sophistication in espresso machine design. While famous for its iconic E61 model, Faema also made its mark in the world of lever operated machines. These elegant devices, characterized by sleek aesthetics and precise engineering, continue to inspire coffee enthusiasts with their timeless appeal and exceptional brewing capabilities.
La Pavoni: A Testament to Italian Craftsmanship
Founded in 1905, La Pavoni holds a special place in the hearts of coffee lovers worldwide. The brand's iconic Europiccola and Professional models are beloved for their elegant designs and unparalleled performance. La Pavoni machines exemplify the artistry and tradition of Italian craftsmanship, offering a timeless charm that continues to enchant baristas and coffee aficionados to this day.
Bezzera: Pioneering Espresso Excellence
Bezzera, founded in 1901, is credited with inventing the first commercial espresso machine, laying the groundwork for modern coffee culture. Alongside its groundbreaking innovations, Bezzera also produced remarkable lever operated machines. With a legacy of over a century of innovation, Bezzera remains a trusted name in the coffee industry, revered for its commitment to quality and excellence.