Lever brewing group parts

On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...

Gaggia steel ballReturn to the Gaggia Italia group overview

Gudgeon pin lever group

La Cimbali brass lever group piston. The piston keeps both springs on it's place and guides them. on the top of the piston the piston shaft is screwed into the top. The piston doesn't come with the seals. they can be found thereReturn to the La Cimbali M15 overview page

This small bushing is used on various domestic lever espresso machines of La Pavoni and Gaggia espresso machines. The La Pavoni part reference for this item is 3140453 and for Gaggia the part reference is S3140453. This bushing can be used on brewing groups pre-millennium as well as millennium brewing groups. The lever fork roller has a outer diameter of...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

The item on this page is a Gaggia lever brewing group spring guide, this item can be found on the Gaggia C70/C80 brewing groups. The spring guide, keeps the main compression spring centred, has been made from pressed copper. Limited stock available

La Pavoni lever group screwReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

Conti lever chromed holderReturn to the Conti lever parts overview

Faema brass cap Return to the Faema Zodiac lever parts overview

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...

On this product page you will find a lever piston used from 03 2006 in various Bezzera lever groups such as the Bezzera Strega, Bezzera Ellisse AL and the Bezzera Ebbis AL. This piston has been made from brass and has a outer diameter of 50mm. The Bezzera part reference for this piston is 5224201

La Pavoni lever pinReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.

Gaggia short cammeReturn to the Gaggia Italia lever group parts overview

The item on this page is a item used on the lever mechanism of various Conti lever brewing groups. The Conti part reference on this item is 202000. This casted brass item is the mid piece of the Conti lever brewing group. This casted piece has 3 bushings installed, this prevents excessive wear on the brass mechanism. You can use this Conti spare part on...

On this page you will find a OEM/Original lever group fork made by the Bezzera brand from Italy. This fork is used in various lever brewing group models with the Bezzera brand. The part reference of this item is 5284501.01NC This lever fork is the connection between the piston and lever itself. This part has been made from casted and machined brass. After...

The item on this product page is a fork pin. This pin connects the piston shaft and the roller in the back to the piston shaft. This pin can be used on various domestic La Pavoni and Gaggia lever espresso machines. This fork pin can be used on pre-millennium as well on millennium espresso machines. The Gaggia part reference is S3140463 and for La Pavoni...

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

Rancilio lever cover. Return to the  Rancilio group parts overview

The item on this page is a OEM/Original La Pavoni spare part. This item is the lever of the lever brewing group. This item is compatible with a lot of pre-millennium as well as millennium brewing groups. This lever can be used on various domestic La Pavoni and Gaggia lever espresso machines. The La Pavoni part reference for this item is 3954004 and for...

Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview

Faema lever group cap Return to the Faema Zodiac lever parts overview

This oddly looking screw is the right brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRDPI  This screw can only be used on the right side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on...

This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.

The item on this page is a is a stainless steel retaining ring. This retaining ring can be used on various domestic lever espresso machines made by Gaggia and La Pavoni. These retaining rings can be used on pre-millennium and millennium lever brewing groups. The Gaggia part reference is S404101 and the Pavoni part reference is 410011. This stainless steel...

The item on this product page is a OEM/original La Pavoni spare part. This chrome nut is used on top of various domestic lever brewing groups made by La Pavoni. This nut can be used on pre-millennium as well as millennium espresso machines. The La Pavoni part reference for this item is 3135014. This nut has on the inside a M10 thread. The outer key size...

La Pavoni lever shaftReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

La San Marco lever handle. The lever doesn't come with the handle and top screw. these can be ordered seperatelyReturn to the  San Marco group parts overview

La Cimbali brewing group stainless steel ball Return to the La Cimbali lever parts overview

Bezzera group elbow fitting Return to the Bezzera lever parts overview

Faema retention valve body Return to the Faema Zodiac lever parts overview

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...

This item is the top section of the lever mechanism used on the Conti lever brewing groups. The Conti part reference on this item is 201800  This chrome plated lever group fork is used to transfer the pulling motion of the lever to a vertical movement. That of the piston. This item has been made from chrome plated brass. This item is available on...

This item is a Conti lever brewing group spare part. It is called a traction support. This item is made from casted brass and has 2 bushings installed into it. This item is available on request.