Home

O ring 23,52x1.78mm epdmReturn to the Faema E61 Legend water inlet parts overview

Rancilio valve gasket 13.5x4x4mm

La San Marco nut for the lever group non return valveReturn to the  San Marco group parts overview

The knock box on this product page is made by the South African company Ribelle. This knockbox can be used by any barista in a domestic as well as in a light commercial setting. The knocbox is different then the traditional drawers and boxed. This knockbox does not have a bar, but a edge where you tab against with your portafilter.  The knockbox has been...

The boiler safety valve on this page can be used on various La Cimbali espresso machines. This valve has a male ¼” BSP-G thread. It has been calibrated at a pressure of 1,8. This valve is a adjustable model. Inside the valve is a FKM seal and a stainless-steel spring. This valve is not certified. Made in Italy You can use this valve on the Cimbali on the...

La Cimbali Microcimbali liberty sight glass gasket

Rancilio PTFE conical gasket 13.7x8.8x6mm

Double nipple female 3/8"

On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...

La San Marco gasket 39,5x50x5,5mmReturn to the  San Marco group parts overview

Faema E61 o ring 18,64x3,53 viton. This o ring seals off the bottom group mushroom. Return to the Faema E61 group parts overview

La Cimbali PTFE gasket. the gaskets seals off the closing nut at the top of the brewing group.return to the La Cimbali overview page

Flat copper gasket 23x17x1.5mm Return to the Faema E61 valve parts overview

Portafilter 2 coffee with chrome plug. Comes with a double filterbasket 14gr

Brass lever valve with PTFE lining

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

The item on this page is a female plug. This female plug can be used with a variety of espresso machine applications. You can use this fitting to plug male threads, don’t forget to order a gasket or thread sealant! This plug has a 1/8” BSP-G thread on the inside. The fitting is made from brass. In some cases it is possible that you get a nickel plated...

La San Marco lever group forkReturn to the La San Marco parts overview

La San Marco steam water valve camme

The item on this page is a sight glass gasket which can be used on various older Gaggia espresso machine models. The sight glass on the Gaggia America has 2 seals, a inner and a outer seal. You can use this gasket for both applications. This gasket is made from EPDM in the Czech Republic.

Brass half nut 1/4" BSP-G  Return to our fitting overview

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...

La San Marco portafilter single spoutReturn to the portafilter overview

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from European walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...

EPDM OR 4,47x1,78

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

This is a extra layer of protection for your Ulka espresso machine vibration pump. When your pump is running dry or way too much then specified, the temperature will rise and eventually electrical components will break down. With this thermal protector your vibration pump will be saved, but the thermal protection will fail. This specific model has a max...

In a commercial and a domestic environment you do need to clean your espresso machine at the end of the day when you have used it, the Puly caff powder is ideal for this application. This specific model of the Puly caff powder contains 900 grams of powder, this is the biggest version so Ideal for a a high volume bar of restaurant. There are 2 smaller...

La Pavoni lever shaftReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...

The copper gasket on this product page can be used on various Bezzera espresso machines. This flat copper gasket is mainly used to seal off the steam and water valves. The Bezzera part reference for this item is 5495001. This copper gasket is flat. The outer diameter is 28mm. the inner diameter is 24mm and the thickness of this gasket is 1mm. You can use...

Custom Faema E61 2 group vintage espresso machine.  The machine has been stripped down, the frame has been shot blasted and coated in black. All chrome plated parts have been powdercoated in 2 types of black and 1 type of red. For the cannopy of the machine we chose crackle black. For the parts which need to be cleaned easily, like the brewing groups...

La San Marco nutReturn to the La San Marco parts overview

La Pavoni steam tap bushing

La Cimbali heat exchanger (HX) has a total length of 210mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...