Home

The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...

La Cimbali m15 rubber o-ring. When the portafilter is locked in this o-ring makes sure that the water doesn't come true the top of the brewing group ring. Return to the La Cimbali lever parts overview

La San Marco portafilter double spoutReturn to the portafilter  overview

On this product page you will find thin walled copper tubing. This tubing has a outer diameter of 6mm, inner diameter of 4mm and a wall thickness of 1mm. This copper is supplied rolled, it does not come in straight lengths. If you order multiple m1, it is possible that you will receive multiple loose lengths. The tubing is sold per M1 This type of copper...

On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...

Faema E61 brass expansion valve nipple Return to the Faema E61 valve parts overview

Stainless steel steam pipe complete

La Cimbali Microcimbali liberty portafilter gasket 60.5x48,5x5mm

L fitting 1/4" FF

La Cimbali Microcimbali liberty piston shaft v gasket

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

It can happen that your old heating element for your La Pavoni Europiccola, La Pavoni Stradivari, La Pavoni Romantica or of your Gaggia 105-106 burns down or get’s a short in it. This specific model heating element gives 1000W at 240V made by the heating element manufacturer Backer. It is a full stainless steel element, so flange and the element. The...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

The portafilter on this product page is a 2 coffee portafilter which can be used on the Conti lever espresso machine groups, as well as the regular solenoid valve operated brewing groups. The filter holder body has the Conti part reference number 4056791. The portafilter has a ear orientation of 90 degree, with a thickness of the ears of 7,5mm. This...

Rancilio thermostat 169°C

La San Marco group showerReturn to the La San Marco product overview

The portafilter gasket shown on this page is used with various espresso machines of the Cimbali group and with Vibiemme espresso machines. the part reference numbers can be found in the extra info tab. This portafilter gasket has been made from NBR. The outer diameter is 74mm the inner diameter is 57,5mm and the thickness is 8mm. This gasket has 4...

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...

Hardened stainless steel insert

Elektra Microcasa sight glass gasket 15x9x8mm

The item on this product page is a steam valve knob for various La Pavoni lever espresso machines. This item is a OEM/Original La Pavoni spare part. The La Pavoni part reference for this item is 475010 This knob has a smooth brass insert. This knob is held in place with a spring pin. This steam valve knob has a silk printed symbol of steam printed on it...

The heating element on this product page is used on various Bezzera espresso machines. The Bezzera part reference numbers for this item are 5722221, 5722246 and 5722423. This heating element produces 3300/3800W at 220/240V.there are in total 4 connecting poles on this heating element. The immersed length is 350mm and the flange has a diameter of 75mm....

Elektra Microcasa portafilter handle wood

Faema e61 Legend o ring level glass 67x60x3.5mmReturn to the Faema E61 Legend sight glass overview

La San Marco gasket supplementReturn to the La San Marco parts overview

Originally you would only find a boiler pressure manometer on the La Pavoni Professional espresso machines. This boiler pressure manometer is mounted on the top sight glass fitting. If you want to convert your La Pavoni Europiccola and fit it with a Pressure gauge, this is the kit you need The sight glass fittings used to have a internal diameter of...

Vibiemme chromed lever sleeve

Brass lever valve with PTFE lining

Faema E61 legend non return valveReturn to the Faema E61 Legend water inlet parts overview

La San Marco lever group balancerReturn to the La San Marco parts overview

La Pavoni lever gasketReturn to the La Pavoni Bar modern parts overview

The solenoid valve on this product page is one made by the company Lucifer. The coil states Parker, this is the main company. This solenoid valve is used in various La Cimbali and Faema espresso machines. This solenoid valve is a 2 way valve. The coil used is a 9W 24V model. The hole diameter is 2,5mm and is sealed off with a FKM seal. The maximum...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

Faema E61 legend sight glasReturn to the Faema E61 Legend sight glass overview

Brass L Fitting 1/8" BSP-G MF Return to our fitting overview