Home

La San Marco steam/water valve pushing ring

Lever ball bearing set for Faema Marte and Mercurio lever groups, only the early curved ones. For the later models Faema Mercurio you need to have a bigger bearing. click there.

Return to the  Rancilio group parts overview Rancilio ball bearing

La Cimbali Liberty microcimbali steam and water valve o ring

La Pavoni boltReturn to the La Pavoni Bar modern parts overview

Filter ring o ring 53,34X5,33mm

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

Astoria heating element 2 group 4000W 230VType flangedwatt 4000volt 230

A rare single group Eterna granprix with a unique design. The machine has been stripped down, the frame has been shot blasted and powder coated. All the body parts off the machine have been re-chromed. All the seals and gaskets have been replaced with new ones. The plastic top has been polished, the top was broken but has been repaired. All the internal...

Return to the  San Marco group parts overview La San Marco group lever

For the La Pavoni Europiccola there haven been a variety of boiler fixing rings. It started in the 60ies with the steel boiler rings, from the 1980’s you will find the brass boiler rings. These have 3 m6 bolt holes for installing the heating element, there is also a attachment point for the ground wire. Around the turn of the century La Pavoni introduced...

Faema brass cap Return to the Faema Zodiac lever parts overview

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

Lip seal 15x8x4

Elektra Microcasa sight glass gasket 15x9x8mm

The gasket on this page is used on various water inlet valves with the brand La Cimbali. The Cimbali part reference number for this item is 401281000 and 401-281-000. The flat gasket has been made from PTFE. The outer diameter is 11,4mm the inner diameter is 8mm and the thickness is 3mm. this gasket has been made in Italy. You can use this gasket on the...

Rancilio steam/water valve stem

On this product page you will find the steam tube for the Elektra Microcasa. This model is the copper brass version. The Elektra part reference for this item is 00151038 This part has the fittings made from plain brass and the tube of it made from copper. This has been lacquered off course, otherwise it would oxidise rapidly.

Faema and Cimbali water inlet valve

This style of flange pump is mainly used on espresso machines of the La Cimbali Group. You can find these pumps on the brands La Cimbali, Faema and Casadio. The Cimbali part references are 2241130177 and 2241-130-177, for Faema they are 1441132497, 2241130177 and 462992000.    This fluid o tech pump has a flange connection. This type of flange connection...

Gaggia Italcrem ball bearingReturn to the Gaggia Italcrem lever group parts overview

La San Marco lever lower valve cap. this cap holds the group gasket holder spring in place.Return to the  San Marco group parts overview

Faema Thermovelox boiler group locking gasket AFM34

The heating element on this page is quite a big model, which goes over 500mm. This specific heating element is made for Astoria and Wega espresso machine models with 3 brewing groups. This heating element is listed with Astoria under 17101 and with Wega the part number is WY17101  This heating element produces 3700W at 230/240V. The heating element has 4...

Brass T fitting 1/8" BSP-G MMM Return to our fitting overview

The filterbasket shown on this product page is a 2 coffee filterbasket suitable solely for a variety of Gaggia espresso machines. Domestic and commercial espresso models. This filter basket has been made by the Italian company IMS Filtri. The part reference for this basket from IMS is GA2T183. Note: this is not a competition basket. This stainless-steel...

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 50 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

On this page you will find a pressure gauge fitting for the domestic La Pavoni lever espresso machines. The part is a original OEM part with the La Pavoni part number 3120104. I want to install a manometer on my La Pavoni Europiccola can I use this item for it? NO. This item is not suitable on a La Pavoni Europiccola espresso machine. The threads used on...

The nut on this product page is a valve shaft closing nut. This nut is used on various Bezzera espresso machines. This item is a OEM/Original spare part. The part reference is 5221804NC. This steam and water valve tap nut is made from machined brass, which has been nickel and chrome plated afterwards. This item is made in Italy. You can use this on the...

Victoria Arduino bottomless portafilterReturn to the portafilter overview

La Cimbali m15 rubber o-ring. When the portafilter is locked in this o-ring makes sure that the water doesn't come true the top of the brewing group ring. Return to the La Cimbali lever parts overview

Vibiemme heating element 1200V 230V Type Thread 1"watt 1200volt 230length (mm) 100

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

There we have a fully restored Faema E61 single group vintage espresso machine. The process always starts with stripping down. to the point that there are a ton of body, frame and brewing group parts. Then the frame will be sand blasted and coated with a 2 layer powdercoating. This is also done for the black trim pieces.Then the original chrome plated...

Vibiemme Filterholder gasket 65.5x55.5x5.5mm originalFor lever group