Home

On this page you will find the heating element gasket, which is an o ring, for the La Pavoni Europiccola, La Pavoni Professional, La Pavoni Stradivari, La Pavoni Romantica and the Gaggia 105-106. This specific gasket is only suitable in combination with the full stainless steel heating elements made by backer. They are not suitable for the earlier brass...

A welding end cap nut is used to put pressure on the welding cap so it seals against the conical surface of it. Once there is not enough pressure from the back from the welding cap nut, the seal won’t work. This type of welding end cap is slightly different then the standard types of caps. To start, this welding end cap is a male thread instead of a...

The single portafilter shown on this product page is a OEM/Original Wega spare part. The part reference for the body of this portafilter is WY27311010, so not the entire portafilter. This portafilter is a 1 coffee model. The spout used has a 3/8” BSP-g thread and is open. The ears have a 90 degree orientation. The thickness of them is 6,5mm. the...

T fitting 1/4" MFF

The item on this product page is a OEM/original La Pavoni spare part. This chrome nut is used on top of various domestic lever brewing groups made by La Pavoni. This nut can be used on pre-millennium as well as millennium espresso machines. The La Pavoni part reference for this item is 3135014. This nut has on the inside a M10 thread. The outer key size...

La Pavoni shaft headReturn to the La Pavoni Bar modern parts overview

Gigleur M5x1mm 0,75mm

The piston gasket on this page is used on various Conti lever brewing groups. The Conti part reference for this item is 200510.  This piston gasket has been made from NBR. The outer diameter is 61mm, the inner diameter is 47mm and the thickness is 6,3mm. This item has been made in France. You can use this piston gasket on the CC100 PM lever brewing...

Brass half nut 1/4" BSP-G  Return to our fitting overview

Astoria Wega dichtung dampf/wasserhahn

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

the portafilter gasket on this page is a OEM/Original Bezzera spare part. The Bezzera spare part reference for this item is 7493008. This item is dimension wise and optically the same as the portafilter gasket as in the accessory tab below. But what is the difference. This gasket has a shore number of 90 and the other gasket has a shore number of 75. The...

On this page you will find a sight glass for various Astoria and Wega espresso machines. The Astoria part number for this sight glass is 21300 and the Wega part number is WY21300. The sight glass has a outer diameter of 11mm and a overall length of 170mm. This sight glass doesn’t have any reference lines. This sight glass of 11x170mm can be used on the...

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...

On this product page you will find a level regulator made by the Italian company Gicar. This level regulator can be used on various Bezzera espresso machines. The Bezzera part reference of this item is 7661034.01  This level regulator has the Gicar code 9.1.24.20G. The part name is RL 30/4ESS/F and runs on 230Vac. This item can be used on models such as...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

La Cimbali heat exchanger (HX) has a total length of 210mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...

La Pavoni Professional boiler gasket. Goes inbetween the boiler and base.Also suitable to use on the bottom for the bakelite flange.

La San Marco washer 30X22X1,5mmReturn to the  San Marco group parts overview

Elektra Microcasa pressure gauge chrome

Rancilio steam valve sleeve

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

Re-production stickers for the Arrarex Caravel temperature contol 1.1 - 1.3. The stickers are full color prints on aluminiumReturn to the Arrarex Caravel parts overview

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Astoria Wega tap joint spring

The item on this page is a lower water level fitting for the Astoria and Wega espresso machines. This item is OEM/Original spare part. The Astoria part number for this item is 53001 and the Wega part number is WY53001  This lower water level fitting has been casted out of brass and is machined afterwards. The fitting which is used to attach the water...

The La Pavoni Shaft Seeger Ring is a high-quality component designed to securely hold the shaft gasket in place in your coffee machine. Made from durable stainless steel, this seeger ring ensures a long-lasting and reliable fit. It meets UNI 7437 and DIN 472 standards, with an external diameter of 21.5 mm. Key Features:Stainless steel construction...

This piston gasket on this product page is one of the 2 used on the Elektra Microcasa a Leva. The reference part number for this item is 00173035. This lip seal has a outer diameter of 41mm a inner diameter of 28mm and a thickness of 6mm.  The shape of this one looks like a W form.

Faema E61 stainless steel expansion valve spring. This spring has a total length of 32.5mm and a external diameter of 15mm.This spring makes sure that the valve opens at the right over pressure. Return to the Faema E61 valve parts overview

On this product page you can find a XP110 pressure switch suitable for the Elektra Microcasa a Leva and the Isomac models Mondiale, Millennium and Tea. The part references for Elektra are01344035. This pressure switch has been manufactured by the company Ma-Ter. The maximum capacity is 15A at 125/250Vac. The maximum working temperature is 125 degree...

All the Faema Lever brewing groups use ball bearings to function properly, they are not all the same btw. The ball bearing set on this page is suitable for the Faema President, Faema Urania, Faema Lambro, Faema Mercurio (with the zodiac type group) and the Faema Zodiac group type. The Faema Marte and first series of the Faema Mercurio use a different...

A refurbished restored Faema Urania 1 group lever espresso machine.It all begins with completely dismanteling of the machine. Then the frame will be shot blasted and powdercoated.Instead of newly chrome plating the machine, this machine was left original. So only cleaning and polishing of the chrome plated parts. to give the chrome a bit of it's shine...

On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the right group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

Faema top valve cap

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview