Home

Faema E61 brass water inlet valve guide. You can use this valve guide for several faema models. But they are mostly used on the Faema E61. comes with the gasket Return to the Faema E61 water inlet overview

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

La Cimbali heat exchanger (HX) ring. This ring spreads equal amount of pressure to the HX and the seal inbetween the HX and the brewing groupreturn to the La Cimbali M20 overview page

La Cimbali Microcimbali liberty portafilter gasket 60.5x48,5x5mm

Vibiemme heating element 1200V 230V Type Thread 1"watt 1200volt 230length (mm) 100

On this page you will find a brass welding cap. These welding caps are used to make a water tight seal between valve components and the copper tubing. This specific model of welding cap needs for soldering 10mm copper tubing. The weld nut used in combination with this welding cap has a 3/8”female thread and a opening in the middle of 13mm.

Bezzera bottomless portafilterReturn to the portafilter overview

Faema and Cimbali water inlet valve

Rancilio flat gasket OR 18x12x3m

the portafilter gasket on this page is a OEM/Original Bezzera spare part. The Bezzera spare part reference for this item is 7493008. This item is dimension wise and optically the same as the portafilter gasket as in the accessory tab below. But what is the difference. This gasket has a shore number of 90 and the other gasket has a shore number of 75. The...

Dichtung Viton 12x3.5x4mm Suitable for:CodeProducer400-274-010 Cimbali400274010 Cimbali

Crushable copper washer 1/4" 18x14x2mm

Safety valve 1/2"1,8 Certif CE PED IV

O ring EPDM 23x3mm. This o ring seals off one side of the one way valve. Return to the Faema E61 valve parts overview

The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.

Brass hose barb 1/2" F 14mm

Rancilio PTFE sight glass classe 6/8 D.10X109mm

La Pavoni bearing pinReturn to the La Pavoni Bar modern parts overview

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...

The o ring on this product page is used on various La Pavoni and Gaggia lever espresso machines. This o ring is used to seal off the steam tube at the steam valve. This o ring can be used on later models pre-millennium and millennium steam valves. The part reference for La Pavoni is 465017. This o ring has been made from FKM. The cord diameter is 1,78mm...

On this page you will find a sight glass for various Astoria and Wega espresso machines. The Astoria part number for this sight glass is 21300 and the Wega part number is WY21300. The sight glass has a outer diameter of 11mm and a overall length of 170mm. This sight glass doesn’t have any reference lines. This sight glass of 11x170mm can be used on the...

Fully restored Faema E61 2 group vintage espresso machine. The machine has been stripped down, the frame has been shot blasted and coated. All chrome plated parts have been re-chromed plated. the stainless steel bits have been grind and polished with a mirror finish. The trim bits on the cannopy have been repainted in black. The 2 group plexiglass has...

La Pavoni showerReturn to the La Pavoni Bar modern parts overview

La Cimbali PTFE gasket. This gasket seals of the brass ptfe holder with the brewing group.Return to the La Cimbali overview page

La San Marco main compression spring guideReturn to the  San Marco group parts overview

Is the grid missing of your La Pavoni Europiccola(324021), Professional, Romantica or Gaggia G105(S324021). You can find the replacement grid on this page. To make your lever espresso machine complete again. This item is suitable for the Pre-millenium and millennium la Pavoni lever espresso machines. The grid has been made out of stainless steel and has...

One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.

A welding end cap nut is used to put pressure on the welding cap so it seals against the conical surface of it. Once there is not enough pressure from the back from the welding cap nut, the seal won’t work. This type of welding end cap is slightly different then the standard types of caps. You will see this type of fitting for instance on the water...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

The gasket on this product page is used on the Faema E61 brewing groups and the E61 style of brewing groups such as with Rocket, La Scala, Grimac, la Pavoni and Wega. The part reference numbers for this gasket can be found in the extra info tab. This gasket is made from AFM34 from the company Victor Reinz. This gasket has good sealing properties, even...

Valve rod washer 12x8x1mm

Lever group attachment screw

Portafilter gasket 71x57x8mm for La Cimbali brewing group made of nbr rubber. This portafilter gasket is also compatible with the La Cimbali M15, Rubino, and Gran Luce espresso machines.

The piston gasket on this page is used on various Conti lever brewing groups. The Conti part reference for this item is 200510.  This piston gasket has been made from NBR. The outer diameter is 61mm, the inner diameter is 47mm and the thickness is 6,3mm. This item has been made in France. You can use this piston gasket on the CC100 PM lever brewing...

This gasket is one of the few ones which does not need to seal off water. But is used as a gasket between 2 metal surfaces. This gasket can be used on various models of domestic La Pavoni lever espresso machines. The part reference for this item is 362019 This gasket has a outer diameter of 93mm a inner diameter of 80mm and a thickness of 2mm. You can use...

La Pavoni Professional boiler gasket. Goes inbetween the boiler and base.Also suitable to use on the bottom for the bakelite flange.