Faema E61 Legend

Faema E61 Legend parts

This page is dedicated to parts for the Faema E61 Legend. This machine was re-introduced around the turn of the century. The faema Legend was made 3 configurations:

·          Faema E61 Legend S1;

·          Faema E61 Legend S2;

·          Faema E61 Legend S3

Esthetically the Faema E61 looks quite a lot like the Faema E61 Legend espresso machine. But technically there are quite a lot off differences.

Water level, the water level used in the Faema E61 legend is one with a casted housing with a sight glass in front. This model is also used on a variety of Faema models like: Faema E92, Faema E97, Faema due and so on   And a variety of La Cimbali models like the La Cimbali M39 and the La Cimbali M39 GT

The pump and motor are nowadays installed inside the machine, traditionally the pump and motor on the Faema e61 could be found outside the machine.

On the Faema E61 legend you can now also find standard a autofill system. So the chance that your heating element will dry boil, because of the lack off water, also reduced a lot. The installation of a safety thermostat inside the element also reduced this a lot.

A other item which has been changed over the time. Is that the traditional mercury pressure switch has been replaced by a new model from Asco (this used to be Sirai)

If you have any questions about your Faema E61 legend espresso machine, don’t hesitate to contact us.

Faema E61 legend

Faema E61 camme holder

The cam holder shown on this page can be used on the Faema E61 and the Faema E61 Legend. The ones used on the E61 style brewing groups have a different shape. The Faema part reference for this item is 4152135911. This item has been machined from a solid piece of brass. After machining and polishing it has been nickel and chrome plated. This item has been...
€40.46

Faema E61 gasket PTFE 36x30x2mm

The PTFE gasket on this page can be used on various E61 style and Faema E61 brewing groups. You can use this gasket on the E61 style brewing groups of the brands like La Scala, Grimac, Wega and La Pavoni.  The part and model references can be found in the extra info tab. This PTFE gasket has a outer diameter of 36mm a inner diameter of 30mm and a...
€1.04

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91

Level indicator red ball

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€2.40

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€20.35

Portafilter gasket 73x57x9mm red silicone

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...
€4.14

IMS E61 style shower screen

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€25.03

E61 style groups shower without welding 60mm

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.32

Faema E61 small square rod 6mm

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...
€1.58

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.84

Faema E61 valve gasket 13x4x4mm

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81

Faema E61 group collector rod gasket holder

The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...
€4.84

Faema E61 group upper plug

The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.65

Faema E61 Legend and Jubilee front lower feet

These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...
€55.37

Faema E61 steam valve pin

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96

Filterholder gasket 72.5x57x8 mm

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...
€4.04

Anti vacuum valve V.A.R. 1/4"

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00

Faema E61 microswitch 16A 250V

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€45.31

Faema E61 microswitch lever control bracket

If you are restoring a Faema E61 or rebuilding a Faema E61 legend it is possible that you find a broken lever mechanism bracket. Now you can replace them. If you start the brewing process on your Faema E61 group, you raise your lever control arm. This pushes down the micro control lever. This control lever is attached to a metal rod. This metal rod is...
€6.24

Washer 14x8x1mm brass

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...
€2.09

E61 valve guide 12mm

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...
€1.74

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€7.53

Faema E61 square shaft 34mm

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.37

Anti vacuum valve TV 1/4"

Anti vacuum valve TV 1/4". Suitable for:CodeProducerA10220 Astra000634 Aurora-brugnetti7452502 Bezzera05062.4.00.09 Brasilia01.00504 Carimali418-911-002 Cimbali418-911-010 Cimbali418911010 Cimbali408898 ContiC219900560 Ecm00200034 Elektra65000205 Expobar2161-118968 Faema2161118968 Faema418911002 Faema...
€10.56

3 phase safety thermostat 169-18°

3 phase safety thermostat 169-18°. Suitable for:CodeProducer20300015 Astoria CMA56302101 Astoria CMA7434001 Bezzera95.01594 Carimali531-193-100 Cimbali02790035 Elektra3231133006 Faema3231135058 Faema531193100 FaemaA1400032 Fiorenzato C.s.0746906 Futurmat-Ariete07476906 Futurmat-Ariete10065832 Lavazza10067254...
€66.77

Faema E61 stainless steel valve rod

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€14.47

Faema E61 Net holder washer 9.8x6.3x1mm

On this page you will find a brass washer which is used in the E61 brewing groups made by Faema. The part references for this item can be found back in the extra info tab. The gasket is used on top of the stainless-steel nozzle filter. The nozzle spring is pushing against this washer to get a equal amount of pressure against the filter This brass washer...
€1.32