Faema E61 Legend

Faema E61 Legend parts

This page is dedicated to parts for the Faema E61 Legend. This machine was re-introduced around the turn of the century. The faema Legend was made 3 configurations:

·          Faema E61 Legend S1;

·          Faema E61 Legend S2;

·          Faema E61 Legend S3

Esthetically the Faema E61 looks quite a lot like the Faema E61 Legend espresso machine. But technically there are quite a lot off differences.

Water level, the water level used in the Faema E61 legend is one with a casted housing with a sight glass in front. This model is also used on a variety of Faema models like: Faema E92, Faema E97, Faema due and so on   And a variety of La Cimbali models like the La Cimbali M39 and the La Cimbali M39 GT

The pump and motor are nowadays installed inside the machine, traditionally the pump and motor on the Faema e61 could be found outside the machine.

On the Faema E61 legend you can now also find standard a autofill system. So the chance that your heating element will dry boil, because of the lack off water, also reduced a lot. The installation of a safety thermostat inside the element also reduced this a lot.

A other item which has been changed over the time. Is that the traditional mercury pressure switch has been replaced by a new model from Asco (this used to be Sirai)

If you have any questions about your Faema E61 legend espresso machine, don’t hesitate to contact us.

Faema E61 legend

E61 brewing group complete rebuild kit

On this product page you will find a rebuild kit for Faema E61 espresso machines. The Faema E61 brewing group is the basis off all the other E61 style of brewing groups made. This does not mean that this kit will fit all those brewing groups. Manufacturers have made over time a lot of changes in the brewing group assemblies, so they are for some...
€84.68

Faema E61 group infusion spring 14x45mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...
€1.62

Faema E61 group upper plug

The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.14

Faema E61 heating element gasket 57x43x3mm

On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
€4.45

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€28.82

Level indicator red ball

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€2.18

Faema E61 group discharge valve

This drain discharge valve can be found on the Faema E61 brewing groups the Wega E61 Style of brewing groups and those of Grimac. The Faema part reference for this item is 4151135920, for Wega WY27421015 and for Grimac it is 1201300035-VBM100. This brass drain jet is installed in the chrome plated drain and breaks the speed of the water coming out of the...
€6.30

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€36.70

Faema E61 camme spring 15x25mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.52

E61 style group spout breaker

On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....
€6.37

Faema E61 stainless steel valve rod

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€13.15

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92

E61 valve guide 12mm

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...
€1.58

Faema E61 valve gasket 15,5x7,5x4mm

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€18.50

Faema E61 group spout breaker

The item shown on this page is the last item on a Faema E61 brewing group, as well on some other e61 style brewing groups. This is the drain fitting which is all the way on the bottom of the brewing group. This model of drain can be used on the brands Faema, Grimac, Pavoni and Wega espresso machines. The Faema part reference for this item is 4152135921,...
€9.31

Faema E61 legend jubilee portafilter single

On this product page you will find a single portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines.. The part reference number for this item is 2771-135 804.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€77.86

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.66

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47

Faema glass support set

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
€45.30

Faema E61 steam/water group expanding spring

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.25

Faema E61 gigleur spring

Faema E61 stainless steel gigleur spring. if your replacing this part don't forget to replace the rest of the sealing parts of the group. We offer a handy rebuilding kit for that. (the gigleur spring is also in that kit) Return to the Faema E61 group parts overview
€1.60

Portafilter gasket 73x57x9mm red silicone

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...
€4.14

Faema E61 filterholder gasket 8.5 mm

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...
€3.38

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.58