Faema E61 Legend

Faema E61 Legend parts

This page is dedicated to parts for the Faema E61 Legend. This machine was re-introduced around the turn of the century. The faema Legend was made 3 configurations:

·          Faema E61 Legend S1;

·          Faema E61 Legend S2;

·          Faema E61 Legend S3

Esthetically the Faema E61 looks quite a lot like the Faema E61 Legend espresso machine. But technically there are quite a lot off differences.

Water level, the water level used in the Faema E61 legend is one with a casted housing with a sight glass in front. This model is also used on a variety of Faema models like: Faema E92, Faema E97, Faema due and so on   And a variety of La Cimbali models like the La Cimbali M39 and the La Cimbali M39 GT

The pump and motor are nowadays installed inside the machine, traditionally the pump and motor on the Faema e61 could be found outside the machine.

On the Faema E61 legend you can now also find standard a autofill system. So the chance that your heating element will dry boil, because of the lack off water, also reduced a lot. The installation of a safety thermostat inside the element also reduced this a lot.

A other item which has been changed over the time. Is that the traditional mercury pressure switch has been replaced by a new model from Asco (this used to be Sirai)

If you have any questions about your Faema E61 legend espresso machine, don’t hesitate to contact us.

Faema E61 legend

Faema E61 microswitch 16A 250V

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€45.31

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€11.52

Faema E61 steam/water group expanding spring

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.48

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82

Stainless ball 8mm

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...
€2.61

Faema E61 boiler manometer

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€43.61

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Filterholder gasket 72.5x57x8 mm

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...
€4.04

Faema E61 steam tap gasket press

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...
€2.32

Faema E61 group net holder

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.67

Faema E61 legend jubilee portafilter single

On this product page you will find a single portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines.. The part reference number for this item is 2771-135 804.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€100.62

Faema glass support set

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
€49.83

Faema E61 square shaft 34mm

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.37

O ring 6.07x1.78mm Solenoid valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.67

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€20.35

Faema E61 complete steam valve

The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000  This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€77.47

Faema E61 group valve guide 11mm

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...
€2.01

Faema E61 lever knob

The handle knob on this page can be used on Faema E61 brewing groups. This handle goes on the brewing group control lever. Originally these were made from Bakelite, but nowadays that isn’t made that much anymore. The Faema part reference fort his item is 4741135910  This plastic lever brewing group handle is made from a shiny plastic. In the middle is a...
€13.25

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71

Faema E61 gigleur spring

Faema E61 stainless steel gigleur spring. if your replacing this part don't forget to replace the rest of the sealing parts of the group. We offer a handy rebuilding kit for that. (the gigleur spring is also in that kit) Return to the Faema E61 group parts overview
€1.76

IMS Faema double cup filterbasket 12/18gr

A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line.  The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03

Faema E61 steam tube

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€34.99

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€7.53

Faema E61 valve rod washer stainless

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.81