La San Marco PTFE HX gasket 34x27x2mm
La San Marco PTFE HX gasket 34x27x2mmReturn to the San Marco group parts overview
€2.04
0
My cart
espresso machine brands
Astoria front stop
On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...
€21.76
Astoria lever pin
On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...
€20.16
La Pavoni Europiccola plastic drain grid
For the La Pavoni Europiccola, Professional and the Romantica there are 2 options to cover the plastic drain tray (371104). The stainless steel drain grid, or the plastic one. On this page you will find the plastic version. This plastic grid has a horizontal grid pattern, instead of the metal one with a hole pattern. The plastic type of grid was...
€15.84
E61 style spring holder
The item on this product page is a spring guide bushing used on various E61 Style of brewing groups. You can use this item with brands such as ECM Heidelberg, La Scala, Bezzera, Isomac, Pavoni and Brasilia. The Bezzera part reference is 7479942, the Brasilia part reference number is 13657.0.00.04, for ECM Heidelberg it is B7479942, for Isomac ISBUS313116...
€5.14
Faema E61 expansion valve guide
Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview
€4.64
Faema lever joint guide right
On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...
€6.97
La Cimbali shower screen spring
La Cimbali M15 and M20 shower screen spring. This stainless steel spring keeps the flat shower screen firmly in place during brewing.To clean the shower screen just gently compress the spring and pull it out. the shower screen will fall out of the brewing group right away.Return to the La Cimbali lever parts overview
€9.64
Faema E61 heating element 2 group 2600W 110V
The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...
€91.45
La Carimali return spring
The item on this product page is a OEM/Original Carimali spare part, it is the lever return spring. So it is not the main compression spring. This spring is available on request.
€38.63
Astoria heating element 2 group 2600W 230V
The heating element on this page is one of the more common heating elements used with Astoria and Wega espresso machine boilers. The Astoria part number is 17051 and the Wega part number for this element is WY17051 The heating element on this page produces 2600W at 230/240V. the heating elements has 4 connecting poles. In between these connectors is a...
€107.13
Bezzera front lever stop
On this product page you will find a front stop for various Bezzera Lever groups. This item has the Bezzera part reference of 5473002.01 You can find this rubber stop on models such as the Bezzera B2000-AL, Bezzera 2006-AL, Bezzera Ebbis AL, Bezzera Ellisse AL and the Bezzera Strega lever group
€17.44
Faema Mercurio boiler gasket
Faema Mercurio boiler gasket 8 hole made from FDA graded fiber materialReturn to the Faema Mercurio parts overview
€28.94
E61 group allen key copper washer 10x6,2x1mm
Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102 This flat copper washer has a outer...
€0.60
La Pavoni Europiccola 12X17X1mm washer
The washer on this product page is a OEM/Original La Pavoni spare part. This washer can be used on various locations with the domestic lever espresso machines made by la Pavoni. The Pavoni part reference for this item is 313003 and for Gaggia the reference is S313003 This washer is suitable for Pre-millennium as well for Millennium espresso machines....
€5.12
Lever group handle
On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....
€13.44
Faema marte/mercurio upper group gasket
Faema marte/mercurio upper group gasket. and how do you need to replace the old one with a new:Unscrew the 4 bolts on top of the group; pull the group assembly out of the brewing group; if you look inside the inner ring has a gasket, remove the old gasket and replace it with the new one; do the above things the other way aroundReturn to the Faema...
€17.66
Portafilter gasket 73x57x9mm
Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.17
Beating rubber lever group
On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...
€11.74
Gaggia lever group pinion gear
It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...
€100.96
Astoria/Wega water level nut 1/2" 12mm
This page shows the water level nut for a Astoria and Wega sight glass. This nut makes sure that the sight glass stays in place and seals properly. If the nut is screwed down the sight glass seal will slightly compress and seal off the sight glass. The part number for this item is for Astoria is 25383 and for Wega WY25383 This sight glass nut has a...
€8.38
La Cimbali piston o ring 34,29X5,33mm
La Cimbali piston o ring 34,29X5,33mm. This thick o ring goes on the piston of a La Cimbali M20 lever brewing groupReturn to the La Cimbali M20 lever group overview
€4.18
La Carimali filterholder gasket 69x57x7,5mm
This portafilter gasket can be used on various La Carimali espresso machines. The part reference for this item is 87.00122.00.19. This gasket has been made from NBR. The outer diameter is 69mm the inner diameter is 57mm and the thickness is 7,5mm. this gasket has been made in Italy. You can use this portafilter gasket on the Carimali Pratica, Carimali E9,...
€3.47
Flex pipe 1500mm 3/8 FF conical base
The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€17.11
AFM 34 gasket 26x21x2mm
This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....
€1.16
Arrarex Caravel stainless tamper European walnut
On this page you will find our tamper for the VAM Caravel and Arrarex Caravel espresso machines. This coffee tamper has a diameter of 43mm. The tamper base has been made out of stainless steel, the handle is made from wood. To be specific european walnut. So make sure that you don’t dip the handle in water. The most important thing is for which model of...
€63.99
Conti portafilter double spout
The portafilter on this product page is a 2 coffee portafilter which can be used on the Conti lever espresso machine groups, as well as the regular solenoid valve operated brewing groups. The filter holder body has the Conti part reference number 4056791. The portafilter has a ear orientation of 90 degree, with a thickness of the ears of 7,5mm. This...
€67.03
Astoria portafilter double spout
Astoria portafilter double spoutReturn to the portafilter overview
€166.35
Arrarex Caravel: A Beacon of Innovation
Founded in the 1950s, Arrarex Caravel quickly rose to prominence with its groundbreaking lever operated espresso machines. The Caravel, the company's flagship model, combined compact design with innovative lever mechanisms, revolutionizing home espresso brewing. Loved for its simplicity and exceptional performance, the Caravel remains a beloved classic among coffee connoisseurs and collectors alike.
La Cimbali: Precision Engineering at Its Finest
La Cimbali, a stalwart in the coffee industry since 1912, is renowned for its commitment to precision engineering and superior quality. While best known for its commercial equipment, La Cimbali also produced exceptional lever operated machines. Models like the M1 showcased the brand's dedication to blending traditional lever brewing with modern technology, setting new standards for excellence in espresso craftsmanship.
Faema: Elevating Espresso to Art
Since its inception in 1945, Faema has been synonymous with innovation and sophistication in espresso machine design. While famous for its iconic E61 model, Faema also made its mark in the world of lever operated machines. These elegant devices, characterized by sleek aesthetics and precise engineering, continue to inspire coffee enthusiasts with their timeless appeal and exceptional brewing capabilities.
La Pavoni: A Testament to Italian Craftsmanship
Founded in 1905, La Pavoni holds a special place in the hearts of coffee lovers worldwide. The brand's iconic Europiccola and Professional models are beloved for their elegant designs and unparalleled performance. La Pavoni machines exemplify the artistry and tradition of Italian craftsmanship, offering a timeless charm that continues to enchant baristas and coffee aficionados to this day.
Bezzera: Pioneering Espresso Excellence
Bezzera, founded in 1901, is credited with inventing the first commercial espresso machine, laying the groundwork for modern coffee culture. Alongside its groundbreaking innovations, Bezzera also produced remarkable lever operated machines. With a legacy of over a century of innovation, Bezzera remains a trusted name in the coffee industry, revered for its commitment to quality and excellence.