Vibiemme Replica Pistone

Faema E61 expansion valve gasket made out of nbr. This gasket makes sure that the expansion valve doesn't leak below the opening pressure of the valve. The gasket itself is seated in a valve guide which also has the function of spring guide for the expansion valve. Return to the Faema E61 valve parts overview

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

Fiorenzato o ring 41,28x3,53mm o ring. This o ring seals the brewing group from the boiler.Return to the Fiorenzato Piazzo San Marco overview

La San Marco lever handle. The lever doesn't come with the handle and top screw. these can be ordered seperatelyReturn to the  San Marco group parts overview

On this page you will find a brass steam pipe bushing. But what is a pipe bushing. A pipe bushing makes it possible to move the steam and water wand freely without leaking. So how does it work? Well the pipe bushing has on the valve side 2 o rings, these seal against the side of the inside of the valve. But on the top ring of the pipe bushing there is...

On this product page you will find a boiler pressure gauge suitable for a variety of Vibiemme espresso machines. The VBM part reference for this manometer is MANM49025GHIR. The pressure gauge can show a boiler pressure from 0 to 2,5bar. The body of the manometer is 49mm, the frame of the pressure gauge is 57mm. This manometer has a capillary with a female...

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

EPDM OR 4,47x1,78

O ring 14x2mm

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...

Vibiemme Replica steam pipe right

Fiorenzato group casting. this casting holds the lever assembly and the spring and piston assembly, offcourse only the casting. Return to the Fiorenzato lever parts overview

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

On this product page you will find a heating element suitable for various VBM heating elements. This heating element is suitable for 2 group Vibiemme boilers. The Vibiemme part reference is ELETRES2G4023. This heating element produces 4000W at 230V and has 4 connecting poles. The immersed length of the heating element is 330mm. the heating element has a...

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

Vibiemme replica steam pipe left

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

When you have just used your steam wand to make a perfect latte. But you want to clean your steam wand, but you can’t because the metal is too hot. Don’t worry, we sell protective rubber sleeves which don’t pass on the heat so you won’t burn your hands. This specific model is suitable for a steam pipe which has a diameter of 10mm and has a length of 50mm....

Lucifer solenoid valve 2 way base mounting 220/240V 50/60Hz

1/4" water charging valve autofill

Complete valve spout 54,6mm

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

Expansion valve nipple

Spring for steam valve

The portafilter gasket on this product can be used on various lever espresso machines. On brands such as Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200194  and the Vibiemme part reference number is GUARSOTPISTON. This portafilter gasket has a outer diameter of 65,5mm a inner diameter of 55,5mm and a thickness of 5,5mm. This gasket...

Ball valve 1/4M 1/4F