Faema E61 spare parts

The Faema E61: A Revolutionary Espresso Machine

The Faema E61 espresso machine is an iconic espresso machine with a timeless design that has revolutionized the espresso machine market. Introduced in the 1961, the Faema E61 marked a significant shift in the way espresso was made, setting new standards for quality and consistency in espresso extraction.

Faema Spare Parts - E61

Faema E61 microswitch lever control bracket

If you are restoring a Faema E61 or rebuilding a Faema E61 legend it is possible that you find a broken lever mechanism bracket. Now you can replace them. If you start the brewing process on your Faema E61 group, you raise your lever control arm. This pushes down the micro control lever. This control lever is attached to a metal rod. This metal rod is...
€6.24

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€97.51

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.74

Flex pipe 2000mm 3/8 ff conical base

On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€20.35

Faema E61 engine RPM 300W 230V

The espresso machine motor on this page is made by the Italian electric motor manufacturer RPM. This motor is intended to be used as a exterior motor, so that it isn’t installed inside the machine. The motor is a good motor to use with a vintage espresso machine like the Faema E61. Currently this coffee machine motor can be used on a variety of models...
€225.40

Faema President and E61 2 group glass

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€303.97

Faema E61 valve gasket 13x4x4mm

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81

Procon clamp ring pump 180 L/H

On this page you will find a espresso machine pump suitable for a variety of espresso machines. This pump has been made by the company Procon in Ireland.  This model is a clamp ring pump, this pump is clamped with a stainless steel clamp to the espresso machine motor. The pump can pump 180 L/H and is fitted with a balanced bypass. To control the pump...
€174.64

Faema E61 heating element 1 group 1500W 110V

Have you ever wanted to convert your single group Faema lever espresso machine from a 220-230V version to a 110V version, now you can. The heating element on this product page is suitable for installation on various antique Faema Lever groups and regular Faema E61 groups. This heating element has the typical Faema type of brass flange. The element is...
€107.56

Faema E61 camme spring 15x25mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.67

IMS Faema double cup filterbasket 12/18gr

A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line.  The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03

Faema E61 microswitch 16A 250V

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€45.31

Faema E61 expansion valve spring

Faema E61 stainless steel expansion valve spring. This spring has a total length of 32.5mm and a external diameter of 15mm.This spring makes sure that the valve opens at the right over pressure. Return to the Faema E61 valve parts overview
€2.42

E61 style groups shower without welding 60mm

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.32

Faema E61 sleeve

The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups.  You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.47

Faema E61 chromed group collector

On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...
€72.40

Faema E61 PTFE gasket 26x21x2mm

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52

E61 style lever brewing group

On this product page you will find a complete E61 style brewing group. There are a variety of E61 style brewing groups. Examples of this are the Solenoid valve groups, with the solenoid valve at the bottom, or on the sides. This E61 style brewing group can be used on Fiorenzato, Grimac and La Scala espresso machines. The Fiorenzato part reference fort his...
€402.24

IMS E61 style shower screen

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€25.03

Faema E61 aluminium filling lever

We where unable to trace down original or reproduction lever handles for the Faema E61 boiler filling valve. So we decided to have them casted ourselves. Seen the alternative would be a plastic handle which didn’t look like at all. We had made a casting mould and have a limited amount made of this Faema E61 aluminium filling handles. You will find this...
€64.31

Faema E61 plastic top 2 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€325.64

Faema E61 pump manometer

On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801  This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€24.38

Faema E61 heating element 3 group 3700W 230V

The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...
€94.05

Faema E61 complete upper pipe

On this product page you will find the complete upper pipe for various E61 style and Faema E61 brewing groups. This item can be used in various E61 style brewing groups such as the ones used on the La Pavoni, Isomac and EC Heidelberg. But also on the Faema E61, Faema E61 Legend and the Faema E61 Jubilee espresso machines. The Faema part reference is...
€33.38

E61 group allen key copper washer 10x6,2x1mm

Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102  This flat copper washer has a outer...
€0.60

Faema E61 stickers

On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....
€11.07

Expansion valve 1/4M adjustable 10-14 Bar

The item on this page is a espresso machine expansion valve. This valve can be used on various espresso machine brands such as La Scala, La Spaziale, La San Marco, Faema and Brasilia. This expansion valve has a male thread which is ¼” BSP-G. This valve is adjustable. The pressure range goes from 10 to 14 bar. For the exhaust water there is a connection...
€28.03

Faema glass support set

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
€49.83

History of the Faema E61

The Faema E61 was introduced in 1961 by the Italian espresso machine manufacturer Faema. It was designed by renowned engineer Ernesto Valente and quickly gained popularity for its innovative features and exceptional performance. One of the key innovations of the Faema E61 was its E61 brewing group, which replaced the traditional lever-operated espresso machines with a more efficient and consistent pump-operated system.

Technical Advancements

The Faema E61 brewing group introduced a number of technical advancements that set it apart from traditional espresso machines. One of the most notable features of the E61 group was its constant pump pressure of 9 bar, which ensured optimal extraction and consistency in every shot of espresso. This revolutionary design paved the way for a new generation of espresso machines and became the basis for many espresso machine manufacturers.

Our Selection of Faema E61 Spare Parts

At our store, we offer a wide selection of spare parts for the Faema E61 espresso machine. Whether you need boiler parts, steam/water valves, body parts, valve parts, brewing group parts, water level parts, pump parts, or water inlet parts, we have you covered. We stock a variety of genuine Faema E61 parts, ensuring that you can find exactly what you need to keep your espresso machine running smoothly.

Faema E61 Models

The Faema E61 espresso machine was produced in various configurations, ranging from 1-group to 6-group models. While the most common models are the 1-group, 2-group, and 3-group versions, there are also larger models available for high-volume commercial settings. Each model features the same innovative E61 brewing group, ensuring consistent performance and quality across the board.

Conclusion

The Faema E61 espresso machine is a true icon of the espresso world, known for its exceptional quality, timeless design, and groundbreaking innovation. With our selection of spare parts, you can keep your Faema E61 running smoothly for years to come, ensuring that you continue to enjoy delicious espresso beverages with every shot. If you have any questions or need assistance finding the right parts for your machine, don't hesitate to reach out to us. We're here to help you keep your Faema E61 in top condition.