Faema No stop valve fitting
Faema No stop valve fitting. pitch 1mm. Suitable for:CodeProducer30370010 Expobar4851117523 FaemaL168/0 Marzocco312226 PavoniRACC3FRUBKO VibiemmeRACCGUIASTEVO Vibiemme
€13.70
0
My cart
espresso machine brands
La Cimbali group locking nut
La Cimbali group locking nut. these nuts screw the inner flange of the brewing group to the brewing group itself. Which makes a air and water tight. Return to the La Cimbali lever parts overview
€6.51
La San Marco lower lever body
La San Marco lower lever body. partially shiny. Return to the San Marco group parts overview
€481.29
Gaggia piston shaft
The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.
€174.30
Gaggia ball bearing
The bearing is essential on a lever espresso machine brewing group. Otherwise it is not possible to transfer the lever movement in a vertical movement. In the brewing group of the Gaggia lever groups the bearings are embedded inside the group. On each side you will find one bearing where the pinion gear can ride on.
€12.34
La Cimbali PTFE gasket
La Cimbali PTFE gasket. This gasket seals of the brass ptfe holder with the brewing group.Return to the La Cimbali overview page
€3.18
La Pavoni Europiccola spring
The big spring shown on this page is a filterbasket spring. This filterbasket spring is used to keep the filterbasket in it’s place. This filter locking spring can be used on pre-millennium as well on Millennium La Pavoni portafilters. The La Pavoni part reference for this item is 311437 You can use this filter locking spring with single as well as with...
€5.76
Brooks 50mm tamper with birch handle
This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 50 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...
€56.04
Faema E61 filterholder gasket 8.5 mm
Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...
€3.38
Flex pipe 2000mm 3/8 ff conical base
On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€18.50
Lever group ball bearing
Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...
€6.95
Faema piston shaft
Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...
€103.85
La Carimali piston ring
The o ring on this product page is the inner piston o ring on the Carimali lever espresso machines. This o ring is made from EPDM. The cord diameter is 3,53mm the inner diameter is 28,17mm and the o ring has been made in Italy.
€1.68
Faema E61 plastic top 2 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€296.04
Astoria Wega steam pipe chrome plated Original part
Astoria Wega steam pipe chrome plated Original part
€52.35
Lever group fibre gasket 22x17x2mm
On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...
€2.54
Aurora Brugnetti inox ball bearing
Aurora Brugnetti inox ball bearing Return to the Aurora-Brugnetti lever parts overview
€2.22
Gaggia Italcrem plate
Gaggia Italcrem plateReturn to the Gaggia Italcrem lever group parts overview
€8.95
Faema E61 heating element 2 group 2440/2900W 220/240V
On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...
€85.61
Brasilia upper level fitting
The water level fitting on this page can be used on various Brasilia espresso machine models. The Brasilia part reference number for this item are 00024.0.00.04 and 00024.0.00.04 This casted brass sight glass fitting has on the machine side a male 3/8” BSP-G thread, on water level side a female 3/8” BSP-G and on the bottom/top a female ¼” BSP-G thread....
€14.66
Gaggia rubber ring
This rubber o ring is used on the Gaggia brewing groups C70/C80 and is used on the flange side of the brewing group. This o ring is made from EPDM and has a cord diameter of 1,78mm and a internal diameter of 25,12mm. This o ring is made in Italy.
€1.90
Faema E61 plastic top 3 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 3 group are only the measurements of the width and length of the U shape.The length of this plexi is about 630mm and the width is 220mm. This cupwarmer...
€321.01
La San Marco PTFE heating element gasket 56x46.5x3mm
La San Marco PTFE heating element gasket 56x46.5x3mm
€3.90
La San Marco steam/water valve inlet gasket 15x5.5x4mm
La San Marco steam/water valve inlet gasket 15x5.5x4mm
€1.19
Brooks 50mm tamper with european walnut handle
This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 50 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from European walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are...
€59.44
Faema lever joint guide left
On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...
€9.60
La San Marco lever lower valve cap
La San Marco lever lower valve cap. this cap holds the group gasket holder spring in place.Return to the San Marco group parts overview
€12.56
Arrarex Caravel: A Beacon of Innovation
Founded in the 1950s, Arrarex Caravel quickly rose to prominence with its groundbreaking lever operated espresso machines. The Caravel, the company's flagship model, combined compact design with innovative lever mechanisms, revolutionizing home espresso brewing. Loved for its simplicity and exceptional performance, the Caravel remains a beloved classic among coffee connoisseurs and collectors alike.
La Cimbali: Precision Engineering at Its Finest
La Cimbali, a stalwart in the coffee industry since 1912, is renowned for its commitment to precision engineering and superior quality. While best known for its commercial equipment, La Cimbali also produced exceptional lever operated machines. Models like the M1 showcased the brand's dedication to blending traditional lever brewing with modern technology, setting new standards for excellence in espresso craftsmanship.
Faema: Elevating Espresso to Art
Since its inception in 1945, Faema has been synonymous with innovation and sophistication in espresso machine design. While famous for its iconic E61 model, Faema also made its mark in the world of lever operated machines. These elegant devices, characterized by sleek aesthetics and precise engineering, continue to inspire coffee enthusiasts with their timeless appeal and exceptional brewing capabilities.
La Pavoni: A Testament to Italian Craftsmanship
Founded in 1905, La Pavoni holds a special place in the hearts of coffee lovers worldwide. The brand's iconic Europiccola and Professional models are beloved for their elegant designs and unparalleled performance. La Pavoni machines exemplify the artistry and tradition of Italian craftsmanship, offering a timeless charm that continues to enchant baristas and coffee aficionados to this day.
Bezzera: Pioneering Espresso Excellence
Bezzera, founded in 1901, is credited with inventing the first commercial espresso machine, laying the groundwork for modern coffee culture. Alongside its groundbreaking innovations, Bezzera also produced remarkable lever operated machines. With a legacy of over a century of innovation, Bezzera remains a trusted name in the coffee industry, revered for its commitment to quality and excellence.