Home

On this product page you will find the main spring for a lever brewing group. This spring is mainly used on older models of Bezzera espresso machines. This spring has a overall length of 131mm. the outer diameter of this compression spring is 46mm. The material used for this spring is just regular spring steel which has been galvanized. You can use this...

On this product page you will find a brass end cap. This end cap has a female thread inside which has a ½”BSP-G thread. This item is made from machined brass. It is possible that you get a version which is also nickel plated.

Faema E61 stainless steel gigleur spring. if your replacing this part don't forget to replace the rest of the sealing parts of the group. We offer a handy rebuilding kit for that. (the gigleur spring is also in that kit) Return to the Faema E61 group parts overview

Gaggia short cammeReturn to the Gaggia Italia lever group parts overview

On this product page you will find a lever piston used from 03 2006 in various Bezzera lever groups such as the Bezzera Strega, Bezzera Ellisse AL and the Bezzera Ebbis AL. This piston has been made from brass and has a outer diameter of 50mm. The Bezzera part reference for this piston is 5224201

Brasilia lower level fitting

Victoria Arduino supervat level gasket Return to the Victoria Arduino lever parts overview

Faema Zodiac spring guide bushing

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

Dow111 Molykote 6gr

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...

Rancilio lever fork. Return to the  Rancilio group parts overview

The item on this product page is a male 3/8” plug. These plugs have various applications, but mainly as it indicates, closing off something. This male plug is normally used with PTFE tape or with a flat gasket/copper gasket. This male plug has a 3/8” thread, the tread type used is a BSP-G thread. This item has been made in Italy.

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

Complete valve spout 54,6mm

La Pavoni Bar lever group shaftReturn to the La Pavoni Bar lever group parts overview

This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The  lever cams do slide over this shaft. This item is not in production anymore.

Gaggia O ring 47,63x3,53mm

Astoria Argenta stainless steel steam pipe

This shower screen is suitable for the pre-millennium La Pavoni lever brewing group, this is only for the domestic lever espresso machines. This filterbasket is manufactured by the Italian company IMS filtri. The shower screen has a outer diameter of 52mm and a height of 14mm. it has been made from stainless steel. The Pavoni part reference for this item...

The item on this product page is a OEM/Original Carimali spare part, it is the lever return spring. So it is not the main compression spring. This spring is available on request.

Astoria Wega tap gasket 13.8x6x4.6mm

Ball valve 1/4M 1/4F

There we have a rare double group La Cimbali Granluce. The machine has the standard M15 La Cimbali lever groups. The machine has been stripped down, the frame has been shot blasted and powder coated. All the body parts off the machine have been re-chromed. All the seals and gaskets have been replaced with new ones. The machine has also been fitted with a...

Every La Pavoni Europcciola, La Pavoni Stradivari and La Pavoni Professional is equipped with a boiler safety valve/pressure relief valve. This item can be used with the pre-millenium and the millennium models. With the earliest models when there is no pressure switch this is the main form of pressure relief of the boiler. The Boiler relief valve is...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

Faema Legend 1 group heating element 220-240V 3000-3570Wcode: 903-553 010

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

Ode 3 way solenoid valve 1/4" 1/4" 220/230V  DN1,5mm. 

Faema marte 1 group espresso machineFully cleaned new safety valve new pressure switch powdercoating of the frame new chrome plating piston gaskets, group gaskets and shower screen replaced. new heat resistant wiring new plexiglass top and back

T fitting 1/4" MFF

Lucifer solenoid valve 2 way base mounting 220/240V 50/60Hz

There we have a rare single group Faema Mercurio third version, with a unique design. All the body parts off the machine have been re-chromed. All the seals and gaskets have been replaced with new ones. The machine has also been fitted with new LED lightingAll the internal parts are as good as new and function like that.The machine will be supplied with...

Arrarex Caravel 2.1 - 3.2 gasket set

"Fully restored La Carimali 1 group espresso machineThe folowing things have done to the machine:Fully cleaned and descaled;new safety valvenew pressure switchpowdercoating of the framenew chrome platingd.new heat resistant wiring

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...