Faema E61 spare parts
The PTFE gasket on this page can be used on various E61 style and Faema E61 brewing groups. You can use this gasket on the E61 style brewing groups of the brands like La Scala, Grimac, Wega and La Pavoni. The part and model references can be found in the extra info tab. This PTFE gasket has a outer diameter of 36mm a inner diameter of 30mm and a...
€0.94
E61 brewing group complete rebuild kit
On this product page you will find a rebuild kit for Faema E61 espresso machines. The Faema E61 brewing group is the basis off all the other E61 style of brewing groups made. This does not mean that this kit will fit all those brewing groups. Manufacturers have made over time a lot of changes in the brewing group assemblies, so they are for some...
€84.68
Faema President and E61 2 group glass
It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€276.34
Faema o ring 7,2X1,9mm nbr
On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...
€0.56
Faema E61 heating element 3 group 3700W 230V
The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...
€85.50
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64
Faema E61 left lower group tube
On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the left group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G
€59.72
Faema E61 single portafilter
The portafilter on this page looks like a classical Faema E61 portafilter. And that is indeed correct, the style looks quite similar to the antique portafilters used in the Faema Lever brewing groups and Faema E61. But there are some slight differences, the shape is slightly different and the end plug in the portafilter handle is not identical to the...
€100.04
Faema E61 heating element 2 group 2440/2900W 220/240V
On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...
€85.61
Faema E61 steam/water group expanding spring
The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.25
Stainless steel clamp for motor/pump
With this motor clamp ring you are able to clamp a flange pump with a motor with a flange motor. The clamp has been made from stainless steel as well for the clamping screw which comes with it. The items have been made in Italy This item is not suitable in combination with pumps used for instance used on the Faema E61 Legend and the Faema E61 Jubile...
€5.14
Faema E61 group upper plug
The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.14
Faema E61 square shaft 34mm
On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.06
Faema E61 filterbasket double 12gr
Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview
€6.46
Compression spring 13x42mm
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...
€2.02
Faema E61 steam tap gasket press
This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...
€2.32
E61 brewing group gasket rebuild kit
E61 brewing group gasket rebuild kit This set is only suitable for the Faema E61 brewing group styles.
€28.80
O ring nbr 8,9x1,9mm
This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview
€0.59
Bottom fitting for boiler pipe 1/2"M 1/2"M, hole 1/4"F
If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...
€17.11
Faema E61 valve gasket 15,5x7,5x4mm
This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74
Boiler top fitting 1/2"
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€19.03
Faema E61 expansion valve nipple
Faema E61 brass expansion valve nipple Return to the Faema E61 valve parts overview
€7.31
Faema E61 boiler manometer
This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€39.65
Faema E61 steam valve nut gasket 23x18x1mm
Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview
€0.82
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Safety valve 3/8'' 1,8 bar
On this page you will find a safety valve which has a male 3/8”BSP-G thread. The pre-set pressure of this valve is 1,8bar. You can adjust it yourself but not recommended. The spring inside the safety valve is made from stainless steel and the sealing material is FKM. The valve has been made in Italy. We do strongly advise to replace the safety valve every...
€15.27
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
IMS E61 style shower screen
This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€22.75
Faema E61 pump manometer
On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801 This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€22.16
Faema E61 steam tube
The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€31.81
Faema E61 sleeve
The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups. You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.16
Faema E61 flange level side
Faema E61 flange sight glass side. Do you have a small leak in one of your boiler flanges. this can be fixed easily by replacing the flange which is leaking. Next to the level side flange we also offer the heating element side flange. Return to the Faema E61 boiler parts overview
€367.22
Washer 14x8x1mm brass
On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569 This brass flat washer has a outer diameter of...
€1.90
Faema E61 Sticker 1 Group
Faema E61 sticker 1 group for the back glass plate of the machine. Return to the Faema E61 body parts overview
€17.47
Faema E61 sticker 2 group
Faema E61 sticker 2 group for the glass plate on the back of the machine. Is your glass plate broken, we do also offer a new glass plate for this sticker. And to finish it off a new set of glass plate nuts Return to the Faema E61 body parts overview
€24.23
