Home

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

The item on this product page is a non return valve used on various La Cimbali and Faema espresso machine models.  The part references of this non return valve are for Faema and Cimbali 958231000. This non return valve is used in the water inlet tap. The body has a diameter of 13,9mm and has a total length of 18,2mm. The valve does not come with the...

Fully restored Faema Urania second series 1 group lever espresso machine.Every restoration starts with inventarisation and after that disassembly. After the disassembly the frame of the machine was sandblasted to remove all the old paint, rust and grime. It got coated with a double layered powdercoating. The next step was re-chrome plating of the original...

Steamtube anti scorch clip 10mm

Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview

Faema digmesa flowmeter cover

On this product page you will find the new model of the Elektra Microcasa a Leva heating element. This element is in voltage and wattage identical to the old one, but that’s it. The element has a flange and a spare tube for a thermostat. The Elektra part reference for this element is 02973011. The element produces 800W at 230V, there are 2 connecting...

Non return valve 3/8M - OUT 3/8M

Rancilio boiler manometer 0 - 2.5 bar. Fitting 1/8" M original

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 58 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are...

The item on this product page is a flat EPDM gasket. This gasket is used on various Bezzera espresso machines as a water inlet valve gasket. This gasket has the Bezzera part reference numbers 5302502, 5493013 and 5493041. This flat gasket is made from EPDM. The outer diameter is 14mm, the inner diameter is 4mm and the thickness is 4mm.

Rancilio heating element gasket 59x45x2mm

Crushable copper washer 22x16x3mm

These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...

La San Marco lever group plate. To this plate the brewing group is fixed to.Return to the  San Marco group parts overview

Faema single portafilter with shiny handle

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...

Vibiemme heating element 1200V 230V Type Thread 1"watt 1200volt 230length (mm) 100

Rancilio brass gasket 13.5mm

Copper tube 12x1mm sold per m0.8If you order multiple lengths, it is possible that you will receive multiple loose lengths

The plastic base plate shown on this page is used with various domestic La Pavoni lever espresso machines. This base plate is a OEM/Original La Pavoni spare part. The La Pavoni part reference for this item is 371174. This plastic base plate is the later model. This base plate is installed from the bottom of espresso machine and held in place with a screw....

Sillicone sight glass gasket when replacing the old sight glass and gaskets on a La Cimbali espresso machine. Also suitable for La Cimbali Rubino and La Cimbali Gran Luce. Return to the La Cimbali lever parts overview

Hardened stainless steel insert

Neuert flange pump 150 L/H compact small shaft

Faema mercurio third series espresso machine.Fully cleaned and descaled; new safety valve new pressure switch powdercoating of the frame new chrome plating piston gaskets, group gaskets and shower screen replaced. new heat resistant wiring new plexiglass top and back

Gaggia boiler gasket

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

This portafilter gasket can be used on various La Carimali espresso machines. The part reference for this item is 87.00122.00.19. This gasket has been made from NBR. The outer diameter is 69mm the inner diameter is 57mm and the thickness is 7,5mm. this gasket has been made in Italy. You can use this portafilter gasket on the Carimali Pratica, Carimali E9,...

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

Gaggia big cammeReturn to the Gaggia Italia lever group parts overview

IMS  Cimbali filterbasket suitable for 1 cup of coffee. The basket itself can contain 6 - 9 grams of coffee.The hole diamter of the baskets is 0,3mmReturn to the IMS filterbasket overview page

Faema E61 expansion valve gasket made out of nbr. This gasket makes sure that the expansion valve doesn't leak below the opening pressure of the valve. The gasket itself is seated in a valve guide which also has the function of spring guide for the expansion valve. Return to the Faema E61 valve parts overview

Faema lever group cap Return to the Faema Zodiac lever parts overview

La San Marco 85 Stainless steel steam pipe

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

PTFE gasket 20x17x2mm. Suitable for:CodeProducer12010 Astoria CMA000466 Aurora-brugnetti000501 Aurora-brugnetti400-215-000 Cimbali400215000 Cimbali401-183-000 Cimbali401-183-010 CimbaliC469900420 Ecm401183000 Faema401183010 Faema4701024558 Faema01539006 Futurmat-Ariete05132808 Futurmat-ArieteISGUATF22172 Isomac...