Home

Valve assembly for steam valve

The item on this product page is a group locking gasket for various Aurora Brugnetti brewing groups. As well as the old lever ones as well for the new solenoid valve operated groups. The Brugnetti part reference number for this item is 000460. This gasket is made from a fibre material. The outer diameter is 78mm, the inner diameter is 42mm and thickness...

Brass half nut 1/2" BSP-G 6mm Return to our fitting overview

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. At some point this seal will leak. This small size you see that it is used in combination...

La Cimbali faema tap joint spring. Suitable for:CodeProducer485-061-010 Cimbali485061010 Faema

La Cimbali heat exchanger (HX) ring. This ring spreads equal amount of pressure to the HX and the seal inbetween the HX and the brewing groupreturn to the La Cimbali M20 overview page

On this product page you will find the Bakelite handle used on various locations on the Elektra Microcasa a Leva. This lever handle can be used on the lever handle and as the portafilter handle. The part reference number of this part is 00469035 This Bakelite handle needs to be screwed into a metal stud which has a M10 thread (00186035)

This sight glass is suitable for the Elektra Microcasa lever espresso machine. With this sight glass you are able to see if there is enough water inside the boiler. The part reference for this sight glass is 00141035. This sight glass has a outer diameter of 9mm and a length of 147mm.

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

Chromed steam stem 4 holes dia 1,5mm

If your m15 lever group is leaking from the showerscreen the chance is big that the piston seals needs to replaced. The La Cimbali v piston seals made out of nbr and are easy to install on the piston. Normally every piston uses 3 piston seals. They are also suited for the La Cimbali Rubino and the La Cimbali Gran Luce. Return to the La Cimbali lever parts...

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...

Brass nut 1/8" BSP-G for 6mm welding capReturn the nut overview page

Puly Milk plus 1000ml cleaning solution. Cleans and sanitizes milk frothers, steam wands and milk pitchers.

The stainless steel pin on this page connects the piston shaft to the lever arm on the Elektra Microcasa a Leva. The part reference for this item is 00180035. This stainless steel pin has a outer diameter of 8mm and a length of 32mm.

La San Marco steam/water stainless steel shaft

On this page you will find a steam nozzle which can be used in combination with some models of Faema, Casadio and La Cimbali. The steam tube has a female 1/8”BSP-Gt thread. On each side of the steam tip there are 2 holes, both have a diameter of 1,5mm. There are 2 flattened spots on the nozzle, so that you are able to install a spanner on it when it is...

Rancilio valve spring 12x22mm

Brass nut 1/2" BSP-G for 12mm welding capReturn the nut overview page

Elektra Microcasa shower screen 52mm original

On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...

La San Marco hot water tube

The 2 coffee filterbasket on this page is suitable for pre-Millennium La Pavoni Lever espresso machines. The La Pavoni part reference for this item is 327051. The IMS part reference for this item is PA2T101/H24/LF This double filterbasket on this page has a outer diameter of 58mm and a height of 24,5mm. This filter basket can hold about 12 grams of ground...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

Faema non return valve plastic holderReturn to the Faema E61 Legend water inlet parts overview

When your M15 lever group compression springs are rusted you can replace them cheaply with new ones. The springs are made spring steel, to prevent rusting their galvanisedInternal spring 150x30mmExternal spring 150x48mm These springs also work on the La Cimbali Rubino and the La Cimbali Gran LuceReturn to the La Cimbali lever parts overview

The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...

Faema E61 boiler 1 group 9LWhen this boiler needs to replace a stainless steel boiler. Some of the pipe work needs to be replaced or remade. It is possible that there are minor dents due to shipping. this is quite common and won't affect the functioning of the boiler.

The washer on this product page is a OEM/Original La Pavoni spare part. This washer can be used on  various locations with the domestic lever espresso machines made by la Pavoni. The Pavoni part reference for this item is 313003  and for Gaggia the reference is S313003  This washer is suitable for Pre-millennium as well for Millennium espresso machines....

The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...

Astoria portafilter gasket 67x56x5.5mm original

La Cimbali Heating element for M15 espresso machine. The flange diameter fo the element is 98mm with 4 holes and probe holders. The element has a length of 230mmType flangedwatt 2700volt 230/380length (mm) 230

Faema E61 legend water level gasket. Return to the Faema E61 Legend sight glass overview

Rocket pump manometer 0 - 20 bar

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...

La Carimali piston spring Return to the Carimali lever parts overview