Home

The small lever shown on this product page is a control lever for starting and stopping the brewing process on the Faema E61 espresso machines. The Faema part reference for this item is 2819136651  This item has been made out of casted aluminium. The small roller installed is made from brass and fixed with a brass rivet. This control lever does not come...

Brass o ring guide

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this page you will find a steam nozzle which can be used in combination with some models of Faema, Casadio and La Cimbali. The steam tube has a female 1/8”BSP-Gt thread. On each side of the steam tip there are 2 holes, both have a diameter of 1,5mm. There are 2 flattened spots on the nozzle, so that you are able to install a spanner on it when it is...

La Cimbali stainless steel portafilter filterbasket for 1 coffee. The filterbasket can contain 7grams of coffee. The basket has a height of 22,5mm and a outside diameter of 68mm. This filterbasket can also be used for the la cimbali rubino and la cimbali gran luce espresso machines.

La San Marco lever group forkReturn to the La San Marco parts overview

O ring 15,88x2,62mm viton

Faema charging valve o ring 4.2x1.9mmReturn to the Faema E61 Legend water inlet parts overview

Crushable copper washer 22x16x3mm

The nut on this product page is a weld-end cap nut. This nut is used to install the pipe with the welded end cap on another fitting. This brass nut is used in combination with a welding accessory. The thread inside is a 3/8” BSP-G female thread. The height of the nut is 16mm and the center hole of this nut is 12.5mm. This brass weld nut can be used in...

Injektor tube 1/4" M 110mm

La Cimbali Piston axle. This axle connects the fork lever of the group with the piston shaft. On the outsides of the la cimbali piston axle there are 2 bearings to make the pull action smoother.

Brasilia lower level fitting

Faema E61 Legend water level plastic coverReturn to the Faema E61 Legend sight glass overview

This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview

Elektra microcasa portafilter brass

La Pavoni ptfe gasketReturn to the La Pavoni Bar modern parts overview

La Pavoni closing plugReturn to the La Pavoni Bar modern parts overview

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.

Safety valve 1/2"1,8 Certif CE PED IV

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

O ring 14x2mm

Faema Marte/Mercurio lower gasket. this is the gasket which makes the inner sleeve water tight.This sleeve can only be safely removed with a custom made key. you can try it with a punch, this can work. but the chance on damaging the part is also present.Return to the Faema parts overview

La San Marco portafilter single spoutReturn to the portafilter overview

This drain discharge valve can be found on the Faema E61 brewing groups the Wega E61 Style of brewing groups and those of Grimac. The Faema part reference for this item is 4151135920, for Wega WY27421015 and for Grimac it is 1201300035-VBM100. This brass drain jet is installed in the chrome plated drain and breaks the speed of the water coming out of the...

La Cimbali conical portafilter gasket Internal diameter (mm) 56External diameter (mm) 70Height (mm) 9

On this product page you will find a rebuild kit for Faema E61 espresso machines. The Faema E61 brewing group is the basis off all the other E61 style of brewing groups made. This does not mean that this kit will fit all those brewing groups. Manufacturers have made over time a lot of changes in the brewing group assemblies, so they are for some...

Faema E61 spout breaker Return to the Faema E61 group parts overview

The earlier models of the La Pavoni Europiccola already had some sort of a protection to keep the sight glass safe. These sight glass protectors were installed at the same moment that the sight glass was installed. Seen they needed to slide over the sight glass completely. In the 1990ies you get the first models of plastic cover, the stainless-steel cover...

This sight glass washer can be used on Gaggia and Brasilia water level assemblies.  This ring spreads the force equally over the sight glass gasket. The Brasilia part reference for this item is 00088.0.00.04 and the part reference for Gaggia is LV0506. This brass washer has a outer diameter of 15mm a inner diameter of 11,5mm and a thickness of 3mm. You...

La Pavoni valve bodyReturn to the La Pavoni Bar modern parts overview

In a commercial and a domestic environment you do need to clean your espresso machine at the end of the day when you have used it, the Puly caff powder is ideal for this application. This specific model of the Puly caff powder contains 370 grams of powder, this is the smallest version so Ideal for a single group espresso machine in domestic use. There are...

The filterbasket shown on this product page is a 2 coffee filterbasket suitable solely for a variety of Gaggia espresso machines. Domestic and commercial espresso models. This filter basket has been made by the Italian company IMS Filtri. The part reference for this basket from IMS is GA2T183. Note: this is not a competition basket. This stainless-steel...

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...