0
My cart
espresso machine brands
Pavoni pre-millenium tamper 49.5mm Birch
This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...
€67.94
Gaggia top nut
This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.
€8.75
Ball bearing lever group
Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview
€23.78
La San Marco group shower
La San Marco group showerReturn to the La San Marco product overview
€6.38
Faema E61 pump manometer
On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801 This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€22.16
Gaggia lever group pinion gear
It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...
€100.96
Faema E61 glass plate srew set
Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92
La San Marco heating element 2 gr 2600W 230V
The heating element on this page is suitable to use on the La San Marco 85 Leva lever espresso machine. The San Marco part reference for this heating element is 108461. This element produces 3000W at 230V. There are in total 4 connecting poles. The immersed length of this element is 375mm. The flange is 82x82mm. This element is mainly for 2 group espresso...
€156.18
Bezzera gasket holder
On this page you will find a brass Bezzera gasket holder, which is suitable for a variety of Bezzera espresso machine models. The Bezzera part references for this item are 7496003 and 5970504. This brass gasket holder normally holds the gasket with the dimensions 19x3.5x4mm, this item does not come with this gasket. To hold this gasket in place there is a...
€14.66
La Pavoni Europiccola and Professional base plate model 2
The plastic base plate shown on this page is used with various domestic La Pavoni lever espresso machines. This base plate is a OEM/Original La Pavoni spare part. The La Pavoni part reference for this item is 371174. This plastic base plate is the later model. This base plate is installed from the bottom of espresso machine and held in place with a screw....
€24.96
La Cimbali group shower
La Cimbali M15 lever stainless steel group shower screen. This screen is clamped in place by a spring.Make sure to remove the shower screen regularly to clean it. A dirty shower screen has influence on the taste of the coffee.Return to the La Cimbali lever parts overview
€8.37
Vibiemme Replica steam tap
With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...
€83.43
Gaggia filterbasket 1 coffee 7gr 68x24.5mm
The single filterbasket on this page can be used on a variety of Gaggia espresso machines. This filter basket is manufactured by the Italian company IMS filtri with the reference of GA1T182. This 1 coffee filterbasket can hold about 7 grams of ground coffee. The outer diameter of this filter basket is 68mm and the height is 24,5mm. The hole pattern is in...
€5.69
Faema E61 heating element gasket 57x43x3mm
On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
€4.45
Faema E61 microswitch 16A 250V
On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€41.19
Faema E61 plastic top 1 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€241.52
La Pavoni Europiccola plastic drain tray
The La Pavoni (and Gaggia) plastic drain tray (371104) is used on a variety of models like the La Pavoni Europiccola, La Pavoni Professional, La Pavoni Romantica and finally On the Gaggia 105(S371104). The plastic drain tray hasn’t been there from the beginning. The first la Pavoni’s had a flat surface where you needed to put your coffee cup. Later on,...
€7.79
La Cimbali HX 150mm
La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...
€32.78
3 phase safety thermostat 169-18°
3 phase safety thermostat 169-18°. Suitable for:CodeProducer20300015 Astoria CMA56302101 Astoria CMA7434001 Bezzera95.01594 Carimali531-193-100 Cimbali02790035 Elektra3231133006 Faema3231135058 Faema531193100 FaemaA1400032 Fiorenzato C.s.0746906 Futurmat-Ariete07476906 Futurmat-Ariete10065832 Lavazza10067254...
€60.70
Flex pipe 1500mm 3/8 FF conical base
The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€17.11
Faema E61 and president 1 group glass
On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...
€234.10
E61 group allen key copper washer 10x6,2x1mm
Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102 This flat copper washer has a outer...
€0.60
Pavoni millenium tamper 51.5mm American walnut
This tamper is made from from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the...
€67.93
La San Marco lever group fork
La San Marco lever group forkReturn to the La San Marco parts overview
€95.37
Neuert flange pump 150 L/H compact small shaft
Neuert flange pump 150 L/H compact small shaft
€136.72
Bezzera filterholder gasket 72x55.5x9.3mm original
the portafilter gasket on this page is a OEM/Original Bezzera spare part. The Bezzera spare part reference for this item is 7493008. This item is dimension wise and optically the same as the portafilter gasket as in the accessory tab below. But what is the difference. This gasket has a shore number of 90 and the other gasket has a shore number of 75. The...
€8.61
Sight glass red lines 11x140 mm
The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140 This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...
€5.67
Arrarex Caravel: A Beacon of Innovation
Founded in the 1950s, Arrarex Caravel quickly rose to prominence with its groundbreaking lever operated espresso machines. The Caravel, the company's flagship model, combined compact design with innovative lever mechanisms, revolutionizing home espresso brewing. Loved for its simplicity and exceptional performance, the Caravel remains a beloved classic among coffee connoisseurs and collectors alike.
La Cimbali: Precision Engineering at Its Finest
La Cimbali, a stalwart in the coffee industry since 1912, is renowned for its commitment to precision engineering and superior quality. While best known for its commercial equipment, La Cimbali also produced exceptional lever operated machines. Models like the M1 showcased the brand's dedication to blending traditional lever brewing with modern technology, setting new standards for excellence in espresso craftsmanship.
Faema: Elevating Espresso to Art
Since its inception in 1945, Faema has been synonymous with innovation and sophistication in espresso machine design. While famous for its iconic E61 model, Faema also made its mark in the world of lever operated machines. These elegant devices, characterized by sleek aesthetics and precise engineering, continue to inspire coffee enthusiasts with their timeless appeal and exceptional brewing capabilities.
La Pavoni: A Testament to Italian Craftsmanship
Founded in 1905, La Pavoni holds a special place in the hearts of coffee lovers worldwide. The brand's iconic Europiccola and Professional models are beloved for their elegant designs and unparalleled performance. La Pavoni machines exemplify the artistry and tradition of Italian craftsmanship, offering a timeless charm that continues to enchant baristas and coffee aficionados to this day.
Bezzera: Pioneering Espresso Excellence
Bezzera, founded in 1901, is credited with inventing the first commercial espresso machine, laying the groundwork for modern coffee culture. Alongside its groundbreaking innovations, Bezzera also produced remarkable lever operated machines. With a legacy of over a century of innovation, Bezzera remains a trusted name in the coffee industry, revered for its commitment to quality and excellence.