Home

La Cimbali PTFE gasket. This gasket seals of the brass ptfe holder with the brewing group.Return to the La Cimbali overview page

There we have a fully restored Faema E61 single group vintage espresso machine. The process always starts with stripping down. to the point that there are a ton of body, frame and brewing group parts. Then the frame will be sand blasted and coated with a 2 layer powdercoating. This is also done for the black trim pieces.Then the original chrome plated...

Vibiemme pump manometer 0 - 16 bar. Fitting 1/8" F

La Cimbali M15 lever stainless steel group shower screen. This screen is clamped in place by a spring.Make sure to remove the shower screen regularly to clean it. A dirty shower screen has influence on the taste of the coffee.Return to the La Cimbali lever parts overview

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...

Rancilio PTFE sight glass classe 6/8 D.10X109mm

La San Marco lever group gasket holderReturn to the la San Marco parts overview

Astoria Wega steam valve gasket holder

This contact thermostat has a shut off temperature at 165 °celcius. In this case it is a manual espresso machine thermostat. That means that it needs to be pushed manually to reset.  With a automatic one it will reset itself. On the bottom of this thermostat is a M4 male screw thread. You can screw the thermostat into a boiler for instance. For a brewing...

On this page you will find a brass gasket holder bushing for the Faema Zodiac brewing group. This bushing transfers the pressure from the outer flow regulator spring to the flat gasket in the back of the brewing group. This ring is made from brass and has an outer diameter of 14,60mm. The inner diameter is 10,00mm. the thickness is 3mm.

Lever group attachment screw

Rancilio valve spring 12.2x31 mm

Brass T fitting 1/8" BSP-G MMM Return to our fitting overview

La Cimbali M15 and M20 shower screen spring. This stainless steel spring keeps the flat shower screen firmly in place during brewing.To clean the shower screen just gently compress the spring and pull it out. the shower screen will fall out of the brewing group right away.Return to the La Cimbali lever parts overview

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...

On this product page you will find the steam tube for the Elektra Microcasa. This model is suitable for the fully chrome plated model. The Elektra part reference for this item is 00151039 This steam wand is identical to the brass and copper one, that’s the material of the items. But these items have been chrome plated.

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...

Valve rod washer 12x8x1mm

Parker 3 way solenoid valve 220/230V 50/60Hz conical ruby 0-10bar. Suitable for:Code Producer18151 Astoria CMA18153 Astoria CMA18157 Astoria CMA18161 Astoria CMA18161996 Astoria CMA18162 Astoria CMA18162002 Astoria CMAA10111 Astra000191 Aurora-brugnetti7702204 Bezzera7702211 Bezzera01947.4.00.08 Brasilia...

La San Marco filterholder gasket 64x53x5,5mmReturn to the  San Marco group parts overview

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

Gaggia Italcrem forkReturn to the Gaggia Italcrem lever group parts overview

1/4" water charging valve autofill

2500W 230v heating element

Nuova Simonelli heating element 3/4 group 5000W 230/380V L 570mm

Faema Marte sight glass axle. This axle is on some models of Faema Marte on the side of the sight glass. It is made from chrome plated brass.Return to the Faema Marte parts overview

The item on this product page is a shaft gasket for the steam valve on various domestic La Pavoni and Gaggia lever espresso machines. This gasket seals off the shaft from the boiler. This shaft gasket can be used on Millennium and Pre-Millennium models. The part reference for La Pavoni is 361023 and for Gaggia it is S361023. This gasket has been made from...

This heating element style you will mainly find with La Cimbali espresso machines. This specific heating element is mainly used with 2 and 3 group espresso coffee machines. The reference part number for Cimbali for this part is 537-012-200 This heating element has a overall length of 390mm. The heating element produces 4500/5370W at 220/240V. The element...

Victoria Arduino supervat level gasket Return to the Victoria Arduino lever parts overview

This flat PTFE gasket is used on various lever espresso machine brewing groups used on the brands Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200190  and the Vibiemme part reference number is GUARTEFANPIST. This flat gasket is made from PTFE. The outer diameter is 50mm, the inner diameter is 44mm and the thickness is 4mm. The gasket...

Anti vacuum valve 1/4" with hose connection 8mm

The single filterbasket on this page can be used on a variety of Gaggia espresso machines. This filter basket is manufactured by the Italian company IMS filtri with the reference of GA1T182. This 1 coffee filterbasket can hold about 7 grams of ground coffee. The outer diameter of this filter basket is 68mm and the height is 24,5mm. The hole pattern is in...

La San Marco lower lever body. partially shiny. Return to the  San Marco group parts overview

Faema E61 legend jubilee level kit

There we have a fully restored Faema Urania second series 1 group lever espresso machine.Every restoration starts with inventarisation and after that disassembly. After the disassembly the frame of the machine was sandblasted to remove all the old paint, rust and grime. It got coated with a double layered powdercoating. The next step was re-chrome plating...