Home

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

On this product page you can find the pre-millennium single filterbasket for the La Pavoni lever brewing group, this is only for the domestic lever espresso machines. This filterbasket is manufactured by the Italian company IMS filtri. This filterbasket has a outer diameter of 58mm and a height of 22mm. This filterbasket can hold around 6 grams of ground...

The item on this product page is a brass washer which can be used on various domestic La Pavoni and Gaggia Lever espresso machines. This includes pre-millennium and Millennium brewing group models. This washer is used in the steam valve. This washer spreads the force equally over the shaft gasket. There are 2 washers installed in each valve. The Gaggia...

Level probe 1/4 125mm

Rancilio PTFE conical gasket 13.7x8.8x6mm

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

La San Marco lever group forkReturn to the La San Marco parts overview

Rancilio lever cover. Return to the  Rancilio group parts overview

Dichtung Viton 12x3.5x4mm Suitable for:CodeProducer400-274-010 Cimbali400274010 Cimbali

T fitting 1/4" MMM

Dow111 Molykote 6gr

Faema E61 brass water inlet valve guide. You can use this valve guide for several faema models. But they are mostly used on the Faema E61. comes with the gasket Return to the Faema E61 water inlet overview

O ring EPDM 23x3mm. This o ring seals off one side of the one way valve. Return to the Faema E61 valve parts overview

On this product page you will find a casted and machined L fitting. This L fitting has a male and a female thread. The Male thread is a ¼”BSP-G thread and on the other side a female ¼”BSP-G thread. This item has been made from brass in Italy. So it is possible that you receive a item in solely brass or a model with a nickel coating.

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 51,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

The item on this product page is our own La Pavoni Europiccola bottomless portafilter. This portafilter is only suitable for the La Pavoni pre-millenium brewing groups. You will find that type of brewing group on la Pavoni lever espresso machines such as the Pavoni Europiccola, Pavoni Professional, Pavoni Mignon. The La Pavoni part reference for this item...

This chrome plated drain valve is used on a variety of espresso machine brands and models which use the E61 style brewing group. The item has a overall length of 26mm and a male thread of ½”. The drain fitting holds the drain jet in place, this part is used a spring support for the drain valve spring. This coffee machine part for the E61 style group is...

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...

Every La Pavoni Europcciola, La Pavoni Stradivari and La Pavoni Professional is equipped with a boiler safety valve/pressure relief valve. This item can be used with the pre-millenium and the millennium models. With the earliest models when there is no pressure switch this is the main form of pressure relief of the boiler. The Boiler relief valve is...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. At some point this seal will leak. This is the biggest size of welding fitting you can...

On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....

Rancilio steam/water valve sleeve

The o ring on this product page is the inner piston o ring on the Carimali lever espresso machines. This o ring is made from EPDM. The cord diameter is 3,53mm the inner diameter is 28,17mm and the o ring has been made in Italy.

La Pavoni rubber ringReturn to the La Pavoni lever group parts overview

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...

Elektra Microcasa sight glass gasket 15x9x8mm

The drain valve on this page is used in a variety of E61 style of brewing groups. You will find this model of drain valve assembly on brands such as Bezzera, ECM Heidelberg, Isomac, La Pavoni, Brasilia, Grimac and Royal. This drain valve comes pre-assembled. The assembly contains the triangular shaped shaft, gasket holder, gasket, flat washer and the...

La Cimbali heat exchanger (HX) ring. This ring spreads equal amount of pressure to the HX and the seal inbetween the HX and the brewing groupreturn to the La Cimbali M20 overview page

San Marco boiler gasket PTFE 165X151X3mm

La Cimbali Microcimbali liberty portafilter gasket 60.5x48,5x5mm

La Cimbali m15 rubber o-ring. When the portafilter is locked in this o-ring makes sure that the water doesn't come true the top of the brewing group ring. Return to the La Cimbali lever parts overview

Puly Grind coffee burr cleaning crystals. Every pack contains 10 doses

La San Marco lever handle. The lever doesn't come with the handle and top screw. these can be ordered seperatelyReturn to the  San Marco group parts overview

A set of our own portafilter and new filterbasket, you can select which type of diameter filterbasket you would like.Basket 1: capacity 14 gr Hole dia: 0,25mmBasket 2: capacity 14 gr Hole dia: 0,30 mm Return to the overview of Arrarex Caravel parts  

O ring epdm 4x2mm