Home

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

The portafilter shown on this product page is a bottomless portafilter which can be used on the famous La Pavoni Lever espresso machines. this model of portafilter is compatible with the La Pavoni Millennium brewing groups. So with the brewing group with the liner inside of the brewing group You can use this brewing group for instance on the La Pavoni...

The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...

The big spring shown on this page is a filterbasket spring. This filterbasket spring is used to keep the filterbasket in it’s place. This filter locking spring can be used on pre-millennium as well on Millennium La Pavoni portafilters. The La Pavoni part reference for this item is 311437 You can use this filter locking spring with single as well as with...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

Gasket PTFE 11.6x8.1x4mm

Faema Mercurio third series pleixglass third series

Fully restored Faema Urania second series 1 group lever espresso machine.Every restoration starts with inventarisation and after that disassembly. After the disassembly the frame of the machine was sandblasted to remove all the old paint, rust and grime. It got coated with a double layered powdercoating. The next step was re-chrome plating of the original...

On this product page you will find a gasket set suitable for the VAM Caravel and Arrarex Caravel lever espresso machines. This model set is not suitable for other models of the Arrarex Caravel then the 1.0 to 1.3 models. This gasket set has the following items in them         1x sillicone portafilter gasket;          1x sillicone o-ring;          2x hpu...

La Cimbali stainless steel portafilter filterbasket for 1 coffee. The filterbasket can contain 7grams of coffee. The basket has a height of 22,5mm and a outside diameter of 68mm. This filterbasket can also be used for the la cimbali rubino and la cimbali gran luce espresso machines.

La Cimbali Liberty microcimbali piston cap o ring

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 58 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are...

Arrarex Caravel 1.3 - 2.1 gasket set

Astoria portafilter single spoutReturn to the portafilter  overview

The single portafilter shown on this product page is a OEM/Original Wega spare part. The part reference for the body of this portafilter is WY27311010, so not the entire portafilter. This portafilter is a 1 coffee model. The spout used has a 3/8” BSP-g thread and is open. The ears have a 90 degree orientation. The thickness of them is 6,5mm. the...

Dichtung Viton 12x3.5x4mm Suitable for:CodeProducer400-274-010 Cimbali400274010 Cimbali

La San Marco brass washerReturn to the  San Marco group parts overview

O ring EPDM 23x3mm. This o ring seals off one side of the one way valve. Return to the Faema E61 valve parts overview

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

M15 HX gasket 93x45x2mm Return to the La Cimbali lever parts overview

Hier is een zeldzame 1 groeps La Cimbali Rubino. Dit model gebruikt de La Cimbali M15 hendel zetgroepen. De volledige machine is uit elkaar gehaald, het frame is gestraald en opnieuw gepoedercoat. Alle verchroomde onderdelen zijn opnieuw verchroomd. De aluminium onderdelen zijn weer opnieuw gepolijst.Daarnaast zijn alle pakkingen en afdichtingen...

This oddly looking screw is the left brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRPIS This screw can only be used on the left side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on the...

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...

The item on this product page is a steam and water valve screw, used on various Brasilia espresso machines. The Brasilia part reference number for this item 00107.4.00.04  This articulating valve screw is used in combination with the spring washers and the conical PTFE gaskets to seal off the valve. This item has been made in Italy. You can use these...

La Pavoni portafilter gasketReturn to the La Pavoni Bar modern parts overview

Brass nipple 1/4" x 3/8" FF BSP-G Return to our fitting overview

On this page you will find a portafilter gasket suitable for various lever brewing groups. This gasket is suitable for pre-millennium groups. The La Pavoni part reference for this item is 2612005 This portafilter gasket has a outer diameter of 60mm a inner diameter of 55mm and a gasket of 5,5mm. This gasket is a square version. This gasket can be used in...

Rancilio brass gasket 13.5mm

La Cimbali PTFE gasket. the gaskets seals off the closing nut at the top of the brewing group.return to the La Cimbali overview page

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

Return to the  Rancilio group parts overview Rancilio ball bearing

Reduction 1/4"F x 3/8"M

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...