Filter by
Price
€ €
Type part
more... less
Filter

Faema lever espresso machine parts

Rediscovering Vintage Faema Espresso Machines: A Journey Through Time

Welcome to our collection of vintage Faema (Fabbrica Apparecchiature Elettro Meccaniche e Affini) espresso machines. In this curated selection, we invite you to explore the rich history and timeless craftsmanship of these iconic machines, including the legendary Faema E61 and its modern successors, as well as the vintage lever-operated models that have left an indelible mark on the world of espresso.

Faema espresso machine spare parts

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91

AFM 34 gasket 26x21x2mm

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....
€1.27

Faema E61 PTFE gasket 26x21x2mm

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52

Faema E61 group spring 14x33mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...
€2.39

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€40.37

Washer 14x8x1mm brass

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...
€2.09

O ring 6.07x1.78mm Solenoid valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.67

Stainless steel clamp for motor/pump

With this motor clamp ring you are able to clamp a flange pump with a motor with a flange motor. The clamp has been made from stainless steel as well for the clamping screw which comes with it. The items have been made in Italy This item is not suitable in combination with pumps used for instance used on the Faema E61 Legend and the Faema E61 Jubile...
€5.65

Faema Urania back plate screw set

On this product page you will find a set of brass nuts and bolts used for the Faema Urania first series and Faema Urania second series. It does happen that these screws and bolts are missing, or just broken off during disassembly This kit contains in total 6 pieces, so 2 for the bottom, 2 for the top and 1 for the side. This item has been made in the EU.
€49.85

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82

Faema bottomless portafilter

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...
€66.43

Faema E61 group collector rod gasket holder

The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...
€4.84

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.84

Anti vacuum valve V.A.R. 1/4"

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00

Faema piston shaft

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...
€103.85

Faema E61 plug for camme holder

This stuffing nut is used to set even pressure on the gaskets of the cam shaft used in the E61 brewing groups. This nut can be used on the classical Faema E61 as well as the modern E61 style brewing groups. Such as Bezzera, La Scala, Grimac, Isomac, Pavoni, Brasilia and Vibiemme. This stuffing nut has been made from nickel and chrome plated brass. The...
€9.81

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€20.35

Boiler top fitting 1/2"

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€20.93

Faema Aluminium group head

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...
€322.51

Faema E61 heating element 1 group 1500W 230V

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...
€102.48

Faema filterbasket 21gr

The 2 coffee filterbasket on this page can be used a big variety of espresso machine brands. You can use this basket on brands such as Faema, Grimac, Astoria, Wega, Rancilio and Conti. This filterbasket has been made by the Italian company IMS Filtri. The IMS part reference is IMS3T011. Note: this is not a competition filterbasket. This stainless steel...
€6.22

Bottom fitting for boiler pipe 1/2"M 1/2"M, hole 1/4"F

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...
€18.82

Lever group shower 57mm

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...
€12.79

Faema Zodiac gasket holder bushing

On this page you will find a brass gasket holder bushing for the Faema Zodiac brewing group. This bushing transfers the pressure from the outer flow regulator spring to the flat gasket in the back of the brewing group. This ring is made from brass and has an outer diameter of 14,60mm. The inner diameter is 10,00mm. the thickness is 3mm.
€9.78

Faema Marte sight glass axle

Faema Marte sight glass axle. This axle is on some models of Faema Marte on the side of the sight glass. It is made from chrome plated brass.Return to the Faema Marte parts overview
€165.82

Filterholder gasket 72.5x57x8 mm

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...
€4.04

Rubber shock absorber for mounting engine

The vibration damper on this page is used to attach espresso and coffee machine motors to a fixed surface. But to prevent the rattling sound and vibrations. The threads used on this vibration damper are a M6 thread. The outer diameter of this part are 20mm and have the same height.
€5.22

Faema E61 and Its Modern Successors

At the forefront of our collection is the iconic Faema E61 espresso machine, a true masterpiece of Italian engineering and design. Introduced in the early 1960s, the Faema E61 revolutionized espresso brewing with its innovative E61 group head, which introduced a pre-infusion chamber and a thermosyphon system for optimal temperature stability. Over the years, the E61 has undergone various iterations, including the Faema E61 Legend and the Faema E61 Jubile, each building upon the legacy of its predecessor with enhancements in performance and functionality.

Vintage Lever Espresso Machines

In addition to the E61 series, our collection also features a selection of vintage lever-operated espresso machines from Faema. These timeless classics, including the Faema Marte, Faema Mercurio, Faema President, Faema Urania, and the beloved Faema Lambro, offer a glimpse into the golden age of espresso brewing. With their elegant design and handcrafted construction, these lever machines evoke a sense of nostalgia while delivering exceptional espresso quality.

Exploring Faema Zodiac Group

For aficionados of lever-operated espresso machines, we've dedicated a special section to the Faema Zodiac group. Known for its reliability and precision, the Faema Zodiac group has been a staple in the world of vintage espresso brewing. With its distinctive design and robust construction, the Zodiac group continues to be a popular choice among espresso enthusiasts seeking the ultimate manual brewing experience.

Authentic Faema Vintage Espresso Machine Parts

At Brooks, we understand the importance of preserving the legacy of vintage Faema espresso machines. That's why we offer a comprehensive selection of authentic parts and accessories for these iconic machines. From piston springs and gaskets to complete brewing groups, portafilter gaskets, heating elements, and body parts, we have everything you need to keep your vintage Faema espresso machine running smoothly.

Custom-Made Solutions

In some cases, finding replacement parts for vintage espresso machines can be challenging. That's why we offer custom-made solutions for heating elements, gaskets, sight glasses, and more. If you're missing a specific part for your Faema espresso machine, don't hesitate to reach out to us. Our team of experts is here to help you find the perfect solution for your restoration project.

Conclusion: Embark on a Journey Through Espresso History

In conclusion, our collection of vintage Faema espresso machines offers a unique opportunity to embark on a journey through espresso history. Whether you're a seasoned barista, a collector of vintage machines, or simply an espresso enthusiast, there's something special waiting for you in our selection. Explore our range of Faema espresso machines and parts today, and rediscover the timeless beauty and craftsmanship of Italian espresso brewing