O ring nbr 8,9x1,9mm
This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview
€0.59
0
My cart
Faema lever espresso machine parts
Flex pipe 2000mm 3/8 ff conical base
On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€18.50
Faema Zodiac gasket holder bushing
On this page you will find a brass gasket holder bushing for the Faema Zodiac brewing group. This bushing transfers the pressure from the outer flow regulator spring to the flat gasket in the back of the brewing group. This ring is made from brass and has an outer diameter of 14,60mm. The inner diameter is 10,00mm. the thickness is 3mm.
€9.78
Faema E61 non return valve body
Faema E61 brass non return valve body. The side flange is screwed into the main body.If you want to complete the assembly add the following parts to the part:Faema E61 Spring Non Return Valve; O Ring EPDM 8,9x1,9mm; Faema E61 Small Non Return ValveReturn to the Faema E61 valve parts overview
€30.34
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64
Faema E61 valve gasket 15,5x7,5x4mm
This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74
Faema E61 filterbasket single 7gr
Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26
Gasket Viton 12x3.5x4mm
Dichtung Viton 12x3.5x4mm Suitable for:CodeProducer400-274-010 Cimbali400274010 Cimbali
€1.18
Flex pipe 1500mm 3/8 FF conical base
The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€17.11
Faema lever joint guide left
On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...
€9.60
Faema E61 glass plate srew set
Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92
Faema E61 right lower group tube
On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the right group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G
€62.10
Faema E61 FDA fiber boiler gasket 12 holes 245x205x2mm
On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...
€30.34
Faema E61 expansion valve nipple
Faema E61 brass expansion valve nipple Return to the Faema E61 valve parts overview
€7.31
IMS Faema double cup filterbasket 12/18gr
A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line. The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€25.48
Faema E61 small square rod 6mm
On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...
€1.44
O ring 6.07x1.78mm Solenoid valve
This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.61
Faema mercurio marte valve guide
Faema mercurio marte valve guide. This is a complete valve guide for the mercurio and marte espresso machines. This one has a shorter valve guide then the E61 model.Return to the Faema parts overview
€32.75