On this product page you will find a steam valve knob suitable for the lever espresso machine Elektra Microcasa. The Elektra part reference for this item is 00154035  With this steam knob you can open and close the steam valve with the turn of the knob.

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

Double nipple female 1/4"

La San Marco steam/water tap handle

On this page you will find a brass washer which is suitable for the Astoria and Wega water level assembly. This washer makes sure that the gasket doesn’t tear when the sight glass nut is tightened. This washer has the Astoria reference 25652 and the Wega part is WY25652  This gasket has a outer diameter of 18mm a inner diameter of 12mm and a thickness of...

Flat copper gasket 23x17x1.5mm Return to the Faema E61 valve parts overview

Faema E61 expansion valve gasket made out of nbr. This gasket makes sure that the expansion valve doesn't leak below the opening pressure of the valve. The gasket itself is seated in a valve guide which also has the function of spring guide for the expansion valve. Return to the Faema E61 valve parts overview

On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...

Faema heating element 2/3 group 4500W 230/380V.Type flangedwatt 4500volt 230/380length (mm) 380Suitable for:CodeProducer17101 Astoria CMA3541135078 Faema911545000 Faema911545010 Faema17104 Wega

Copper gasket 26x20,5x2mm

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. This size of welding end cap is mainly used for making tubing for pressure switches. So...

La Pavoni Europiccola and Professional base plate model 1.This model is suitable for the base with the screw hole in the drain pan base

On this product page you will find a boiler pressure gauge suitable for a variety of Vibiemme espresso machines. The VBM part reference for this manometer is MANM49025GHIR. The pressure gauge can show a boiler pressure from 0 to 2,5bar. The body of the manometer is 49mm, the frame of the pressure gauge is 57mm. This manometer has a capillary with a female...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find a pump pressure gauge which can be used with various brands such as Bezzera and ECM Heidelberg. The part reference for Bezzera is 7432523 and for ECM Heidelberg is B7432517  This pump pressure gauge goes from 0 to 16 bar. The case of this manometer has a diameter of 39mm, the frame is 44mm. The connection at the back is...

IMS E61 style shower screen 60mm

Faema E61 spout breaker Return to the Faema E61 group parts overview

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

valve rod washer 22.15x13x1.2. Suitable for:CodeProducer590-715-000 Cimbali590715000 Faema

La Cimbali Microcimbali liberty piston shaft gasket

La Cimbali M15 and M20 shower screen spring. This stainless steel spring keeps the flat shower screen firmly in place during brewing.To clean the shower screen just gently compress the spring and pull it out. the shower screen will fall out of the brewing group right away.Return to the La Cimbali lever parts overview

La San Marco steam/water valve spring driving bowl

Gasket PTFE 11.6x8.1x4mm

T fitting 3/8"FFM

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...

The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...

Conti bottomless portafilterReturn to the portafilter overview

Rancilio steam/water valve joint o ring 12,1x2,7mm

La Cimbali heat exchanger (HX) ring. This ring spreads equal amount of pressure to the HX and the seal inbetween the HX and the brewing groupreturn to the La Cimbali M20 overview page

La San Marco gasket 39,5x50x5,5mmReturn to the  San Marco group parts overview

On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the right group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G

Astoria heating element 4500W 230/380V L 310mmType                       flangedwatt 4500volt                      230/400length (mm) 310

This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview

Faema zodiac circulation limiter