On this product page you will find a conical PTFE gasket suitable for a variety of La San Marco espresso machines. The La San Marco part reference for this item is 109049  The conical PTFE gasket has a outer diameter of 12,5mm a inner diameter of 7mm and a thickness of 5,5mm. This gasket seals off the Steam and water valve shaft off. This gasket has...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 50 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are...

Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102  This flat copper washer has a outer...

Vibiemme heating element 1600W 250V Type Thread 1 1/4"watt 1600volt 250length (mm) 95

Gigleur M5x1mm 0,75mm

This item is a conical ptfe gasket, which is used on various Bezzera espresso machines. This item is a OEM/Original Bezzera spare part. The Bezzera part reference number for this item is 5494002.  This conical gasket is made from PTFE. The outer diameter is 16,5mm, the inner diameter is 6mm and the thickness is 5,5mm. This gasket is made in Italy. You can...

On this page you will find a group locking gasket. This group locking gasket is normally used with most Astoria espresso machine and some Wega machines, so not lever groups. But they are also suitable for the Astoria and Wega lever groups This gasket is made from a fibre material. The outer diameter is 88 mm, the inner diameter is 40mm and the thickness...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....

Bezzera bottomless portafilterReturn to the portafilter overview

Faema top valve cap

If your m15 lever group is leaking from the showerscreen the chance is big that the piston seals needs to replaced. The La Cimbali v piston seals made out of nbr and are easy to install on the piston. Normally every piston uses 3 piston seals. They are also suited for the La Cimbali Rubino and the La Cimbali Gran Luce. Return to the La Cimbali lever parts...

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

On this product page you will find a lever pin suitable for various Bezzera Lever brewing groups. This lever pin can be used on the Bezzera Ellisse Al, Bezzera Ebbis Al, Bezzera Strega, Bezzera B2000 AL and the Bezzera B2006 AL. The Bezzera part reference for this item is 5244007CN This steel lever pin has a diameter of 9mm and a length of 26mm.

Return to the  San Marco group parts overview La San Marco group lever

La Cimbali M15 lever stainless steel group shower screen. This screen is clamped in place by a spring.Make sure to remove the shower screen regularly to clean it. A dirty shower screen has influence on the taste of the coffee.Return to the La Cimbali lever parts overview

Faema E61 sticker 1 group for the back glass plate of the machine. Return to the Faema E61 body parts overview

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

Victoria Arduino bottomless portafilterReturn to the portafilter overview

The portafilter on this product page is a 2 coffee portafilter which can be used on the Conti lever espresso machine groups, as well as the regular solenoid valve operated brewing groups. The filter holder body has the Conti part reference number 4056791. The portafilter has a ear orientation of 90 degree, with a thickness of the ears of 7,5mm. This...

Faema Mercurio third series pleixglass third series