The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...

Injektor tube 1/4" M 110mm

O ring epdm 4x2mm

The nut on this product page is a weld-end cap nut. This nut is used to install the pipe with the welded end cap on another fitting. This brass nut is used in combination with a welding accessory. The thread inside is a 3/8” BSP-G female thread. The height of the nut is 16mm and the center hole of this nut is 12.5mm. This brass weld nut can be used in...

On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the right group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G

This flat rubber gasket is used on a variety on Gaggia lever brewing groups. This flat gasket is used to seal of the regulator rod on the back of the brewing group. This gasket itself is made from NBR and is made in the Czech Republic.

On this page you will find a stainless steel filterbasket. This filterbasket is suitable for the La Pavoni Post millennium brewing groups. This single filterbasket has a outer edge which is 60mm. the height of the filterbasket is 20,5mm The filterbasket itself can hold approximately 7 grams of ground coffee for a single coffee. For which models is this...

Brass nut 1/2" BSP-G for 14mm welding capReturn the nut overview page

On this page you will find a heating element used in Vibiemme(ELETRESD80022) espresso machines. To be precise in the dual boiler of the Vibiemme Replica and Vibiemme Chimaera. But it also used in the domestic espresso machine the Vibiemme Domobar Super. This specific heating element produces 800W with 230V on 50/60Hz. The element has 2 connections both...

Puly caff plus powder 570gr nsf. cleaning powder for solenoid valve brewing groups.

The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T  This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio and Faema Lever brewing groups. The outer diameter of this piston gasket is 50mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio Z9,...

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...

IMS La San Marco lever group showerReturn to the IMS shower screen overview page

On this product page you will find the portafilter gasket for the Bezzera Strega. This portafilter gasket is a OEM/original Bezzera spare part. The Bezzera part reference for this item is 7493020 This portafilter gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 7,5mm.

La Cimbali heat exchanger (HX) ring. This ring spreads equal amount of pressure to the HX and the seal inbetween the HX and the brewing groupreturn to the La Cimbali M20 overview page

This espresso machine motor is made by the Italian company RPM (model number 11002728). The motor itself has 165W with 230V 50/60hz. To power the motor up it has a capacitor of 10 µf. This is one of the more standardized espresso machine motors and is being used by a variety of coffee machine manufacturers. This pump is a clamp ring motor. So the...

On this product page you will find a precision shower screen which is suitable for Post millennium La Pavoni and Gaggia lever brewing groups which have a 54mm brewing group. This item is manufactured by the Italian company IMS Filtri and has the article number PA200IM54 The external diameter of this shower screen is 54mm, the internal diameter is 49mm and...

The portafilter on this product page is a 2 coffee portafilter which can be used on the Conti lever espresso machine groups, as well as the regular solenoid valve operated brewing groups. The filter holder body has the Conti part reference number 4056791. The portafilter has a ear orientation of 90 degree, with a thickness of the ears of 7,5mm. This...

Suitable for the new Faema E61 Legend and Jubilee

Lever ball bearing set for Faema Marte and Mercurio lever groups, only the early curved ones. For the later models Faema Mercurio you need to have a bigger bearing. click there.

La San Marco inox brewing group rodReturn to the La San Marco parts overview

Astoria Wega heating element 1 gr 2000W 230VType flangedwatt 2000volt 230length (mm) 180

The pressure switch on this page is the Asco P303T02, Asco used to be the company Sirai. This pressure switch is used on various espresso machine brands such as Casadio and La Cimbali. The part references are for Casadio 532195500 and for Cimbali 532-195-500. This pressure switch is a 3 poles 20A model. The connection at the bottom is a ¼” BSP-G with a...

Gaggia XD heating element 2 gr 4000/4760W 230VType flangedwatt 4000/4760volt 220/240length (mm) 310

The sight glass on this page can be used on various domestic La Pavoni and Gaggia lever espresso machines. this level glass can be used on various versions of the pre-millennium Pavoni espresso machines as well on all millennium espresso machine models. The Gaggia part reference is S453101 and the Pavoni part reference is 453101. This sight glass has a...

Nuova Simonelli heating element gasket 67x55x3mm

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Rancilio brass washer

The big spring shown on this page is a filterbasket spring. This filterbasket spring is used to keep the filterbasket in it’s place. This filter locking spring can be used on pre-millennium as well on Millennium La Pavoni portafilters. The La Pavoni part reference for this item is 311437 You can use this filter locking spring with single as well as with...

EPDM OR 4,47x1,78

Faema lever group cap Return to the Faema Zodiac lever parts overview

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...

La San Marco silicone level gasket 19x31x3mm