Faema heating element 2/3 group 4500W 230/380V.Type flangedwatt 4500volt 230/380length (mm) 380Suitable for:CodeProducer17101 Astoria CMA3541135078 Faema911545000 Faema911545010 Faema17104 Wega

Faema / Cimbali expansion valve

The item on this product page is a OEM/Original Bezzera spare part. This item is a manual water inlet valve, which has the Bezzera part reference number 5964055. This valve can comes assembled and complete, so it is ready to install right away. You can use this water inlet valve on the various Bezzera lever operated espresso machines. Such as the Bezzera...

The item on this page you will find a OEM/Original La Pavoni spare part. This nut can be used on La Pavoni pre-millennium and millennium lever brewing groups. This nut is used as a counter nut for the shaft nut. The La Pavoni part reference for this item is 3135264. This nut has a internal M10 thread. The key size for this nut is 14mm. the height of this...

Neuert flange pump 150 L/H compact small shaft

On this page you will find a NTC thermistor sensor, or just NTC. These probes are connected to a PID, this sensor basically reads the temperature inside the boiler. This specific item is used with the Rocket R 60V and the Rocket R58 espresso machine (A199904679). But this NTC probe is also used in a variety of Vibiemme models like the Vibiemme Domobar...

La San Marco steam/water stainless steel shaft

Astoria Wega gasket 15x4x4mm

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Brass T fitting 1/8" BSP-G MMM Return to our fitting overview

La Cimbali Liberty microcimbali piston cap o ring

OR 7.59x2.62mm viton. Suitable for:CodeProducer7496016 Bezzera00837.0.00.02 Brasilia401-366-000 Cimbali401366000 Cimbali402-220-000 Cimbali402220000 Faema4701-116687 Faema4701116687 Faema10064149 Lavazza140325161 Saeco

Every La Pavoni Europcciola, La Pavoni Stradivari and La Pavoni Professional is equipped with a boiler safety valve/pressure relief valve. This item can be used with the pre-millenium and the millennium models. With the earliest models when there is no pressure switch this is the main form of pressure relief of the boiler. The Boiler relief valve is...

The pressure switch on this page is the Asco P303T02, Asco used to be the company Sirai. This pressure switch is used on various espresso machine brands such as Casadio and La Cimbali. The part references are for Casadio 532195500 and for Cimbali 532-195-500. This pressure switch is a 3 poles 20A model. The connection at the bottom is a ¼” BSP-G with a...

On the back of the Faema Zodiac brewing group is a top nut and a bottom nut. The top nut needs to be sealed off. Otherwise the water will leak out of it. You would have the choice of a fibre gasket but also a PTFE gasket. On this page you will find the PTFE gasket. The dimensions of this PTFE gasket measure a outer dimension of 15mm a inner dimension of...

The La Pavoni (and Gaggia) plastic drain tray (371104) is used on a variety of models like the La Pavoni Europiccola, La Pavoni Professional, La Pavoni Romantica and finally On the Gaggia 105(S371104). The plastic drain tray hasn’t been there from the beginning. The first la Pavoni’s had a flat surface where you needed to put your coffee cup. Later on,...

The item on this page is a OEM/Original La Pavoni espresso machine part. This boiler knob can be used on various domestic lever espresso machines. This item has the La Pavoni part references 26872 and 47700308  This boiler knob screws in the top of the boiler. This boiler knob does not come with the sealing o ring. The knob has been made in the EU. You...

Faema non return valve plastic holderReturn to the Faema E61 Legend water inlet parts overview

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

Rancilio sight glass 12 x 140 mm

Rancilio stainless steel steam pipe

Faema Mercurio third series pleixglass third series

Vibiemme replica steam pipe left

Astoria Wega heating element 3 gr 5000W 230/380VType flangedwatt 5000volt 230/380length (mm) 570

Brass half nut 1/2" 6mm

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

The item on this page is a sight glass gasket which can be used on various older Gaggia espresso machine models. The sight glass on the Gaggia America has 2 seals, a inner and a outer seal. You can use this gasket for both applications. This gasket is made from EPDM in the Czech Republic.

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

Faema marte/mercurio upper group gasket. and how do you need to replace the old one with a new:Unscrew the 4 bolts on top of the group; pull the group assembly out of the brewing group; if you look inside the inner ring has a gasket, remove the old gasket and replace it with the new one; do the above things the other way aroundReturn to the Faema...

Faema la cimbali water inlet spring

On this product page you will find a brass T fitting, which is solely male. This fitting has on each side a male ½”BSP-G thread. This item is made from casted brass and machined afterwards. It is possible that you receive a item which is brass or nickel plated brass.

valve rod washer 22.15x13x1.2. Suitable for:CodeProducer590-715-000 Cimbali590715000 Faema

La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...

La Cimbali steam water valve handle. Suitable for M28-M30-M31-M32

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...