Filter by
Filter

Faema E61 Jubilé

Faema E61 Jubilee spare parts

The Faema E61 legend and the Faema E61 jubilee are re-introduced around the turn of the century. The design was kept the same, but technically the machine was updated to with modern features. Like replacing the mercury switch with a modern Sirai pressure switch, temperature probe and with the newer machines a internal pump.

With the introduction of the Faema E61 jubilee lifted the traditional machine to a new level. This model is solenoid operated instead of with the manual valves like with the original Faema E61. Which is standard for a modern espresso machine.

In this overview you can find most parts for the Faema E61 legend and Faema E61 jubilee espresso machine. If you can't find the parts your looking for just send a email.

Faema E61 Jubilé spare parts

Faema E61 legend jubilee portafilter single

On this product page you will find a single portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines.. The part reference number for this item is 2771-135 804.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€100.62

Faema E61 boiler manometer

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€43.61

IMS Faema single cup filter basket 7/9 gr

The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59

Faema E61 plastic top 1 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€265.67

Level indicator red ball

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€2.40

E61 style groups shower without welding 60mm

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.32

Faema E61 complete upper pipe

On this product page you will find the complete upper pipe for various E61 style and Faema E61 brewing groups. This item can be used in various E61 style brewing groups such as the ones used on the La Pavoni, Isomac and EC Heidelberg. But also on the Faema E61, Faema E61 Legend and the Faema E61 Jubilee espresso machines. The Faema part reference is...
€33.38

Faema E61 valve rod washer stainless

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.81

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59

Faema E61 group upper plug

The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.65

Faema E61 Net holder washer 9.8x6.3x1mm

On this page you will find a brass washer which is used in the E61 brewing groups made by Faema. The part references for this item can be found back in the extra info tab. The gasket is used on top of the stainless-steel nozzle filter. The nozzle spring is pushing against this washer to get a equal amount of pressure against the filter This brass washer...
€1.32

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€11.52

O ring 6.07x1.78mm Solenoid valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.67

Faema E61 valve gasket 15,5x7,5x4mm

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.81

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€7.53

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Faema E61 gigleur spring

Faema E61 stainless steel gigleur spring. if your replacing this part don't forget to replace the rest of the sealing parts of the group. We offer a handy rebuilding kit for that. (the gigleur spring is also in that kit) Return to the Faema E61 group parts overview
€1.76

Faema E61 steam tap gasket press

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...
€2.32

Faema E61 gasket PTFE 22x16x2mm

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34

Faema E61 pump manometer

On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801  This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€24.38

Flex pipe 1500mm 3/8 FF conical base

The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€18.82

Faema E61 steam valve pin

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96

Faema E61 steam tube

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€34.99

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.74