0
My cart
Faema E61 Jubilé
Faema E61 steam valve knob
On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€18.50
Faema front bakelite knob set
It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€36.70
O ring 23,52x1.78mm epdm
O ring 23,52x1.78mm epdmReturn to the Faema E61 Legend water inlet parts overview
€1.27
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Faema E61 filterbasket single 7gr
Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26
Faema E61 valve rod washer stainless
This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101 This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.74
O-ring 17,17X1,78mm EPDM
O-ring 17,17X1,78mm EPDMReturn to the Faema E61 Legend water inlet parts overview
€2.26
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€10.91
Faema E61 group net holder
This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.43
Faema E61 heating element gasket 57x43x3mm
On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
€4.45
Washer 14x8x1mm brass
On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569 This brass flat washer has a outer diameter of...
€1.90
Faema E61 moustache set
On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€28.82
O ring 3.69x1.78mm viton
O ring 3.69x1.78mm vitonReturn to the Faema E61 Legend water inlet parts overview
€0.52
Faema E61 gasket PTFE 36x30x2mm
The PTFE gasket on this page can be used on various E61 style and Faema E61 brewing groups. You can use this gasket on the E61 style brewing groups of the brands like La Scala, Grimac, Wega and La Pavoni. The part and model references can be found in the extra info tab. This PTFE gasket has a outer diameter of 36mm a inner diameter of 30mm and a...
€0.94
Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9W
Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview
€80.75
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
Faema non return valve plastic holder
Faema non return valve plastic holderReturn to the Faema E61 Legend water inlet parts overview
€3.30
Faema E61 glass plate srew set
Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92
Faema E61 legend water level gasket
Faema E61 legend water level gasket. Return to the Faema E61 Legend sight glass overview
€3.18
Portafilter gasket 73x57x9mm
Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.17
Faema E61 group upper plug
The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.14
Faema E61 legend jubilee portafilter double
On this product page you will find a double portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines. The part reference number for this item is 2771-135 803.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€90.92
Faema E61 legend jubilee portafilter single
On this product page you will find a single portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines.. The part reference number for this item is 2771-135 804.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€77.86
Faema E61 legend non return valve
Faema E61 legend non return valveReturn to the Faema E61 Legend water inlet parts overview
€16.76
Brewing group gigleur 0.6mm
Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines Return to the Faema E61 group parts overview
€1.58
Faema E61 legend sight glass
Faema E61 legend sight glasReturn to the Faema E61 Legend sight glass overview
€9.77
Faema E61 steam valve nut gasket 23x18x1mm
Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview
€0.82
Faema E61 valve gasket 15,5x7,5x4mm
This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74
Rubber pump motor connector 35mm
The item on this page is a rubber motor coupling. This coupling can be used on various Faema and Cimbali espresso machines. There are 2 types of couplings the 35mm and the 40mm coupling. This is the 35mm This coupling is used on the Faema E61 legend and Faema E61 Jubilee espresso machines, the 40mm coupling won’t fit this application. The Faema part...
€11.52
Faema e61 rubber foots 25x6mm
It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
€4.16
Faema E61 inox filter 10.5x0.3mm
On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894. This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.66
Faema E61 valve rod spring
This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.13