On this product page you will find a T fitting. This T fitting has on each side a female connection. The threads used are 1/8” BSP-G thread. The fitting is made from casted and machined brass in Italy. It is possible that you get a plain brass item or a nickel plated one. For functioning that doesn’t matter.

La Cimbali Liberty microcimbali piston gasket o ring

La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...

T Fitting 3/8" FFF

On this product page you will find a brass T fitting, which is solely male. This fitting has on each side a male ½”BSP-G thread. This item is made from casted brass and machined afterwards. It is possible that you receive a item which is brass or nickel plated brass.

The stainless steel compression spring on this page is used on various Bezzera steam and water valves. The part reference for this Bezzera compression spring is5471504  The compression spring has a outer diameter of 14mm and a height of 10mm. This item can be used on various Bezzera models such as the Bezzera Galatea, Bezzera Ellisse, Bezzera Ebbis,...

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. At some point this seal will leak. This small size you see that it is used in combination...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

The portafilter on this page is suitable for a post millennium brewing group used by La Pavoni and Gaggia Lever espresso machines, the ones for domestic use. This portafilter is Not suitable for the older pre-millennium brewing groups. The Gaggia part number for this item is S395307 and for La Pavoni the part number is 395307R  The portafilter is a...

Is the lever fork on your Faema Lever group worm out, this is the solution for it. When you have a aluminium lever fork or brass one where there is slack on the lever pint, it is time to replace it. The item on this page is a brass casted and chrome plated lever fork for the Faema lever brewing groups, of course not for all models. You can use this model...

Switch protective cover

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

Re-production stickers for the Arrarex Caravel temperature contol 1.1 - 1.3. The stickers are full color prints on aluminiumReturn to the Arrarex Caravel parts overview

One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.

Solenoid valve connector. Suitable for:CodeProducer18110 Astoria CMAA10113 Astra000564 Aurora-brugnetti7631504 Bezzera00697.4.00.08 Brasilia7000/C Olab9007775 Reneka

O ring  5.7x1.9mm nbr

Gaggia group locking gasket FDA gradedReturn to the Gaggia Italia group overview

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

The single filterbasket model shown on this page is mainly used on Astoria and Wega espresso machines. Note: this basket can be used on any portafilter which has a similar 70mm outer diameter filterbasket. This single coffee filterbasket has been made by the Italian filterbasket manufacturer IMS Filtri, their reference number for this item is CM1T007....

Faema E61 legend non return valveReturn to the Faema E61 Legend water inlet parts overview

Brass nipple 3/8" x 3/8" MM BSP-G Return to our fitting overview

Gicar level regulator RL30/1E/2C/F 115V

La Cimbali conical portafilter gasket Internal diameter (mm) 56External diameter (mm) 70Height (mm) 9

The bottomless portafilter on this product page can be used on a variety of Astoria espresso machines. The Astoria part reference number for this item is 27311004.  The portafilter has a ear orientation of 45 degree, the ear thickness is 6mm. The portafilter does come with a double filter basket and stainless steel spring. This portafilter is made in...

La Cimbali Heating element for M15 espresso machine. The flange diameter fo the element is 98mm with 4 holes and probe holders. The element has a length of 230mmType flangedwatt 2700volt 230/380length (mm) 230

Parker 3 way solenoid valve 220/230V 50/60Hz conical ruby 0-10bar. Suitable for:Code Producer18151 Astoria CMA18153 Astoria CMA18157 Astoria CMA18161 Astoria CMA18161996 Astoria CMA18162 Astoria CMA18162002 Astoria CMAA10111 Astra000191 Aurora-brugnetti7702204 Bezzera7702211 Bezzera01947.4.00.08 Brasilia...

Vibiemme infusion valve 41.5mm

The item on this page is a OEM/Original La Pavoni espresso machine part. This boiler knob can be used on various domestic lever espresso machines. This item has the La Pavoni part references 26872 and 47700308  This boiler knob screws in the top of the boiler. This boiler knob does not come with the sealing o ring. The knob has been made in the EU. You...

Crushable copper washer 22,8x17x3mm 3/8"

The earlier models of the La Pavoni Europiccola already had some sort of a protection to keep the sight glass safe. These sight glass protectors were installed at the same moment that the sight glass was installed. Seen they needed to slide over the sight glass completely. In the 1990ies you get the first models of plastic cover, the stainless-steel cover...

La Cimbali Microcimbali liberty portafilter gasket 60.5x48,5x5mm

IMS La San Marco lever group showerReturn to the IMS shower screen overview page

Copper crushable washer 21x17x2mm

The heating element gasket on this page can be used on a variety of Bezzera espresso machine heating elements. The Bezzera part reference number for this item is 5492006 This gasket has a outer diameter of 76mm a inner diameter of 40mm and a thickness of 2mm. The material used is a fibre material. The Bezzera models you can use this on are the Bezzera...

La Cimbali Piston axle. This axle connects the fork lever of the group with the piston shaft. On the outsides of the la cimbali piston axle there are 2 bearings to make the pull action smoother.