On this page you will find a NTC thermistor sensor, or just NTC. These probes are connected to a PID, this sensor basically reads the temperature inside the boiler. This specific item is used with the Rocket R 60V and the Rocket R58 espresso machine (A199904679). But this NTC probe is also used in a variety of Vibiemme models like the Vibiemme Domobar...

This heating element style you will mainly find with La Cimbali espresso machines. This specific heating element is mainly used with 2 and 3 group espresso coffee machines. The reference part number for Cimbali for this part is 537-012-200 This heating element has a overall length of 390mm. The heating element produces 4500/5370W at 220/240V. The element...

The item on this product page is a flat gasket used on various applications on the Gaggia and La Pavoni lever espresso machines. You can use this gasket on the sight glass fittings and the sight glass top nut. As well as on our conversion kit for the Manometer. The part reference for Gaggia for this item is S362021 and for Pavoni it is 362021.  This...

La Pavoni portafilter gasket 60x50x5,5mm. Only suitable for Millenium machines

Rancilio Clever DX steam valve

The newer model of la Pavoni Europiccola and all the models of the Pavoni Professional use a modern pressure switch.  Currently those are the Ma-ter Echo pressure switches. Seen these can’t be installed directly into the heating element (the pressure switch would stick out the bottom off the base). For this problem they have found a solution. In the...

On this product page you will find a steam valve knob suitable for the lever espresso machine Elektra Microcasa. The Elektra part reference for this item is 00154035  With this steam knob you can open and close the steam valve with the turn of the knob.

The o ring on this product page is used on various La Pavoni and Gaggia lever espresso machines. This o ring is used to seal off the steam tube at the steam valve. This o ring can be used on later models pre-millennium and millennium steam valves. The part reference for La Pavoni is 465017. This o ring has been made from FKM. The cord diameter is 1,78mm...

Brass nipple 3/8"M x 1/2"M BSP-G Return to our fitting overview

Copper crushable washer 21x17x2mm

E61 style upper sleeve. not for faema e61

The shower screen on this product page is quite unique. This is a Conti lever espresso machine shower screen. This shower screen has 3 bolt holes instead of the traditional 1 bolt hole. This shower screen has the part reference of 072200  This stainless-steel shower screen has in total 3 mounting holes. The outer diameter of this shower screen is 57mm....

The o ring on this product page is the inner piston o ring on the Carimali lever espresso machines. This o ring is made from EPDM. The cord diameter is 3,53mm the inner diameter is 28,17mm and the o ring has been made in Italy.

IMS cimbali 2 coffee filterbasket. The basket can contain 12/18grams of coffee.The hole diameter of the baskets is 0,3mm.Return to the IMS filterbasket overview page

This Nuert pump is one of the few espresso machine pumps made in stainless steel. The majority of all the pumps are still made from low lead brass. This specific pump is designated as a “Compact Plus “pump and has the part number PRM15FZXN_EGND. This pump is specially made for the espresso machines models made by the La Cimbali group. There are a few key...

Non return valve 3/8M - OUT 3/8M

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...

Filter ring o ring 53,34X5,33mm

Faema E61 double portafilter for E61 type group

Gaggia big cammeReturn to the Gaggia Italia lever group parts overview

The sleeve on this page is used in various millennium La Pavoni lever groups, as well as the domestic Gaggia lever groups. The part reference of this plastic sleeve for La Pavoni is 371133 and for Gaggia the part reference is S371133. This sleeve is a OEM/Original La Pavoni part. This item is used in combination with a o ring which has a inner diameter of...

Faema gas gasket 52x2mm

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

The nut on this product page is a weld-end cap nut. This nut is used to install the pipe with the welded end cap on another fitting. This brass nut is used in combination with a welding accessory. The thread inside is a 3/8” BSP-G female thread. The height of the nut is 16mm and the center hole of this nut is 12.5mm. This brass weld nut can be used in...

On this product page you will find a boiler gasket suitable for various Faema Urania boilers. This item is suitable for the first series of Faema Urania espresso machines. Not for the later ones which have similar boiler styles as the E61 and president. This PTFE boiler gasket has a outer diameter of 195mm a inner diameter of 155mm. The gasket has 9 holes.

The o ring on this page can be used as a seal between the lever brewing group and the water boiler of a variety of La Pavoni domestic lever espresso machine models. The La Pavoni part reference for this item is 465128 This o ring is not suitable for the old models, the ones which screw into the boiler. Besides that you can use this o ring on every group....

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

Seeger ring 9mm

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...

On this page you will find our own Brooks microfiber cleaning cloths. These cloths are ideal for cleaning your espresso machine, coffee grinder or just the work surface around your espresso machine. This is not the standard household dust cleaning cloth your standard find. This type of microfiber is a lot softer used to clean finer surfaces like car...

Faema spring for P4 valve. Suitable for:CodeProducer30370040 Expobar4731-103918 Faema4731103918 Faema08389900 Futurmat-Ariete10391803 Futurmat-ArieteL165/4 Marzocco311427 Pavoni9007705 Reneka10402014 SanremoMOLLAASTAREVO VibiemmeMOLLAASTARUBK Vibiemme

La Pavoni safety valve M22 code 395221G

On this product page you will find a Bezzera Strega support lever group compression spring. This item is a OEM/Original spare part from Bezzera. The part reference for this item is 5471538  This stainless steel compression spring has a length of 78mm and a outer diameter of 28mm. Dit is not the main brewing group lever spring. That is a spring which is...

Astoria heating element 4500W 230/380V L 310mmType                       flangedwatt 4500volt                      230/400length (mm) 310